Refereed Journal Papers:
93 Z. Wang, W. Xiong, D.S-K. Ting, R. Carriveau, Z. Wang, “Comparison of underwater and underground CAES systems for integrating floating offshore wind farms,” Journal of Energy Storage, accepted.
92 I. Arianmehr, D.S-K. Ting, S. Ray, “Convection heat transfer of a flat plate in the wake of a turbulence generator,” Heat Transfer Research, 48: xx-xx, Article HTR-11984, in press, 2017.
91 K. Bassett, R. Carriveau, D.S-K. Ting,“Underwater energy storage through application of Archimedes principle,” Journal of Energy Storage, available on line, j.est.2016.07.005.
92 I. Arianmehr, D.S-K. Ting, S. Ray, “Convection heat transfer of a flat plate in the wake of a turbulence generator,” Heat Transfer Research, 48: xx-xx, Article HTR-11984, in press, 2017.
91 K. Bassett, R. Carriveau, D.S-K. Ting,“Underwater energy storage through application of Archimedes principle,” Journal of Energy Storage, available on line, j.est.2016.07.005.
90 F. Fouladi, P. Henshaw, D.S-K. Ting, S. Ray, “Flat plate convection heat transfer enhancement via a square rib,” International Journal of Heat and Mass Transfer, 104: 1202-1206, 2017.
89 K. Bassett, R. Carriveau, D.S-K. Ting, “Experimental analysis of buoyancy battery energy storage system,” Renewable Power Generation, DOI: 10.1049/iet-rpg.2016.0033 , Online ISSN 1752-1424 Available online: 23 September 2016.
88 Z. Wang, W. Xiong, D.S-K. Ting, R. Carriveau, Z. Wang, “Conventional and advanced exergy analyses of an underwater compressed air energy storage system,” Applied Energy, 180: 810-822, 2016.
87 D. C. J. Rice, R. Carriveau, D.S-K Ting, “Commercial greenhouse water demand sensitivity analysis: single crop case study,” Water Science and Technology: Water Supply, 16(3): DOI: 10.2166/ws.2016.031, 13 pages, 2016.
86 S. Alhasan, R. Carriveau, D.S-K. Ting, “A review of adsorbed natural gas storage technologies,” Journal of Environmental Studies, 73(3): 343-356, 2016.
85 M. Ahmadi-Baloutaki, R. Carriveau, D.S-K. Ting, “A wind tunnel study on the aerodynamic interaction of vertical axis wind turbines in array configurations,” Renewable Energy, 96(A): 904-913, 2016.
84 A. Raeesi, S. Cheng, D.S-K. Ting, “Application of a three-dimensional aeroelastic model to study the wind-induced response of bridge stay cables under unsteady wind conditions,” Journal of Sound and Vibration, 375: 217-236, 2016.
83 Z. Wang, D.S-K. Ting, R. Carriveau, W. Xiong, Z. Wang, “Design and thermodynamic analysis of a multi-level underwater compressed air energy storage system,” Journal of Energy Storage, 5: 203-211, 2016.
82 H. Cen, R. Carriveau, D.S-K. Ting, “Effect of mass ratio on the hydrodynamic response of a flexible cylinder,” Journal of Marine Science and Application, 15(1): 50-62, 2016.
81 F. Fouladi, P. Henshaw, D.S-K. Ting, “Effect of a triangular rib on a flat plate boundary layer,” Journal of Fluids Engineering, 138(1), 011101:1-11, 2016.
80 A.R. Vasel-Be-Hagh, R. Carriveau, D.S-K. Ting, J.S Turner, “On the drag of buoyant vortex rings,” Physical Review E, 92:043024, 1-6, DOI: 10.1103/PhysRevE.92.043024, 2015.
79 K. Bassett, R. Carriveau, D.S-K. Ting,“3D printed wind turbines Part 1: Design considerations and rapid manufacture potential,” Sustainable Energy Technologies and Assessments, 11:186-193, 2015.
78 M. Ahmadi-Baloutaki, R. Carriveau, D.S-K. Ting, “Performance of a vertical axis wind turbine in grid turbulence,” Sustainable Energy Technologies and Assessments, 11: 178-185, 2015.
77 H. Cen, M. Ahmadi-Baloutaki, D.S-K. Ting, R. Carriveau, “Mitigating flow-induced vibration of a flexible circular cylinder via pre-tension,” Sustainable Energy Technologies and Assessments, 11:173-177, 2015.
76 A.R. Vasel-Be-Hagh, R. Carriveau, D.S-K. Ting, “Structural analysis of an underwater energy storage accumulator,” Sustainable Energy Technologies and Assessments, 11:165-172, 2015.
75 C.G. Cvetkovski, S. Reitsma, T. Bolisetti, D.S-K. Ting, “Heat transfer in a U-bend pipe: Dean number versus Reynolds number,” Sustainable Energy Technologies and Assessments, 11:148-158, 2015.
74 M. Ahmadi-Baloutaki, R. Carriveau, D.S-K. Ting, “An experimental study on the interaction between free-stream turbulence and a wing-tip vortex in the near-field,” Aerospace Science and Technology, 43: 395-405, 2015.
73 U. Asad, M. Zheng, D.S-K. Ting, J. Tjong, “Implementation challenges and solutions for homogeneous charge compression ignition combustion in diesel engines,” Journal of Engineering for Gas Turbines and Power, 137/101505, 9 pages, 2015.
72 A.R. Vasel-Be-Hagh, R. Carriveau, D.S-K. Ting, “A balloon bursting underwater,” Journal of Fluid Mechanics, 769: 522-540, 2015.
71 J. Smith, R. Carriveau, D.S-K. Ting, “Turbine power production sensitivity to coastal sheared and turbulent inflows,” Wind Engineering, 39(2): 183-192, 2015.
70 A.R. Vasel-Be-Hagh, R. Carriveau, D. S-K. Ting, “Flow over submerged energy storage balloons in closely and widely spaced floral configurations,” Ocean Engineering, 95(1): 59-77, 2015.
69 F. Fouladi, P. Henshaw, D.S-K. Ting, “Turbulent flow over a flat plate downstream of a finite height perforated plate,” Journal of Fluids Engineering, 127(2): 021203, 12 pages, 2015.
68 G. Martínez-Narro, P.F. Henshaw, D.S-K. Ting, “Mexico’s shoreline as a site for the transition to renewable energy,” International Journal of Environmental Studies, 71(6): 877-886, 2014.
67 I. Arianmehr, D.S-K. Ting, S. Ray, “Effect of a transverse groove on cooling of a surrogate photovoltaic panel,” International Journal of Environmental Studies, 71(6): 850-861, 2014.
66 C.G. Cvetkovski, S. Reitsma, T. Bolisetti, D.S-K. Ting, “Ground source heat pumps: should we use single U-bend or coaxial ground exchanger loops?,” International Journal of Environmental Studies, 71(6): 828-839, 2014.
65 A.R. Vasel-Be-Hagh, R. Carriveau, D.S-K. Ting, “Flow past an accumulator unit of an underwater energy storage system: three touching balloons in a floral configuration,” Journal of Marine Science and Application, 13: 467-476, 2014.
64 J. Smith, R. Carriveau, D.S-K. Ting, “Inflow parameter effects on wind turbine tower cyclic loading,” Wind Engineering, 38(5): 477-488, 2014.
63 B.C. Cheung, R. Carriveau, D.S-K. Ting, “Parameters affecting scalable underwater compressed air energy storage,” Applied Energy, 134: 239-247, 2014.
62 B.C. Cheung, R. Carriveau, D.S-K. Ting, “Multi-objective optimization of an underwater compressed air energy storage system using a genetic algorithm,” Energy, 74: 396-404, 2014.
61 M. Ahmadi-Baloutaki, R. Carriveau, D.S-K. Ting, “Straight-bladed vertical axis wind turbine rotor design guide based on aerodynamic performance and loading analysis,” Proceeding of Institution of Mechanical Engineers, Part A: Journal Power & Energy, 228(7): 742-759, 2014 (one of two winners of the SAGE Best Paper Prize in 2014 by the editorial board of Journal of Power and Energy).
60 P. McKay, R. Carriveau, D.S-K. Ting, J. Jehrendt, “Global sensitivity analysis of wind turbine power output,” Wind Energy, 17(7): 983-995, 2014.
59 A. Raeesi, S. Cheng, D.S-K. Ting, “A two-degree-of-freedom aeroelastic model for the vibration of dry cylindrical body along unsteady air flow and its application to aerodynamic response of dry inclined cables,” Journal of Wind Engineering and Industrial Aerodynamics, 130: 108-124, 2014.
58 A. R. Vasel-Be-Hagh, R. Carriveau, D. S-K. Ting, “Underwater compressed air energy storage improved through vortex hydro energy,” Sustainable Energy Technologies and Assessments, 7: 1-5, 2014.
57 J. Aman, D. S-K. Ting, P. Henshaw, “Residential solar air conditioning: energy and exergy analysis of an ammonia-water absorption cooling system,” Applied Thermal Energy, 62: 424-432, 2014.
56 A.R. Vasel-Be-Hagh, R. Carriveau, D.S-K. Ting, “Energy storage using weights hydraulically lifted above ground,” International Journal of Environmental Studies, 70(5): 792-799, 2013.
55 F. Fouladi, P. Henshaw, D.S-K. Ting, “Enhancing smart grid realization with accurate prediction of photovoltaic performance based on weather forecast,” International Journal of Environmental Studies, 70(5): 754-764, 2013.
54 M. Ahmadi-Baloutaki, R. Carriveau, D.S-K. Ting, “Effect of free-stream turbulence on flow characteristics over a transversely-grooved surface,” Experimental Thermal and Fluid Science, 51: 56-70, 2013.
53 A.R. Vasel-Be-Hagh, R. Carriveau, D. S-K. Ting, “Numerical simulation of flow past an underwater energy storage balloon,” Computers and Fluids, 88: 272-286, 2013.
52 M. Ahmadi-Baloutaki, D.S-K. Ting, R. Carriveau, “The role of free-stream turbulence on flow evolution in the wake of a VAWT blade,” Wind Engineering, 37(4): 401-420, 2013.
51 A.R. Vasel-Be-Hagh, D.S-K. Ting, R. Carriveau,“Correlating flow pattern with force coefficients in air flow past a tandem unit of three circular cylinders,” International Journal of Fluid Mechanics Research, 40(3): 1-19, 2013.
50 A. Raeesi, S. Cheng, D.S-K. Ting, “Aerodynamic damping of an inclined circular cylinder in unsteady flow and its application to the prediction of dry inclined cable galloping,” Journal of Wind Engineering and Industrial Aerodynamics, 113: 12-28, 2013.
49 P. McKay, R. Carriveau, D.S-K. Ting, “Wake impacts on downstream wind turbine performance and yaw alignment,” Wind Energy, 16: 221-234, 2013.
48 N. Younis, D.S-K. Ting, “The subtle effect of integral scale on the drag of a circular cylinder in turbulent cross flow,” Wind and Structures, 15(6): 463-480, 2012.
47 B. Cheung, N. Cao, R. Carriveau, D.S-K. Ting, “Distensible air accumulators as a means of adiabatic underwater compressed air energy storage,” International Journal of Environmental Studies, 69(4): 566-577, 2012.
46 J. Bas, J. Smith, R. Carriveau, S. Cheng, D.S-K. Ting, T. Newson, “Structural response of a commercial wind turbine to various stopping events,” Wind Engineering, 36(5): 553-569, 2012.
45 J. Konrad, R. Carriveau, M. Davison, F. Simpson, D.S-K. Ting, “Geological compressed air energy storage as an enabling technology for renewable energy in Ontario, Canada,” International Journal of Environmental Studies, 69(2): 350-359, 2012.
44 A. Raeesi, S. Cheng, D.S-K. Ting, “Some insight into the wind-induced vibration of stay cables in the context of rigid static inclined circular cylinder,” Journal of Applied Fluid Mechanics, 5(2): 99-112, 2012.
43 N. Cao, D.S-K. Ting, R. Carriveau, “Correlating a high-lift airfoil performance with turbulence strain rate,” Wind Engineering, 35(5): 589-606, 2011.
42 K. Bassett, R. Carriveau, D.S-K. Ting, “Vibration response of a 2.3 MW wind turbine to yaw motion and shut down events,” Wind Energy, 14(8): 939-952, 2011.
41 P. McKay, R. Carriveau, D.S-K. Ting, “Farm wide dynamics: the next critical wind energy frontier,” Wind Engineering, 35(4): 397-418, 2011.
40 N. Cao, D.S-K. Ting, R. Carriveau, “The performance of a high-lift airfoil in turbulent wind,” Wind Engineering, 35(2): 179-196, 2011.
39 N. Moradian, D.S-K. Ting, S. Cheng, “Advancing drag crisis of a sphere via the manipulation of integral length scale,” Wind and Structures, 14(1): 35-53, 2011.
38 K. Bassett, R. Carriveau, D.S-K. Ting, “Vibration analysis of 2.3 MW wind turbine operation using the discrete wavelet transform,” Wind Engineering, 34(4): 375-388, 2010.
37 M. Younis, T. Bolisetti, D.S-K. Ting, “Ground source heat pump systems: current status,” International Journal of Environmental Studies, 67(3): 405-415, 2010.
36 N. Moradian, D.S-K. Ting, S. Cheng, “The effects of freestream turbulence on the drag coefficient of a sphere,” Experimental Thermal and Fluid Science, 33: 460-471, 2009.
35 A. Raeesi, S. Cheng, D.S-K. Ting, “Spatial flow structure around a smooth circular cylinder in the critical Reynolds number regime under cross-flow condition,” Wind and Structures, 11(3): 221-240, 2008.
34 M. Islam, D.S-K. Ting, A. Fartaj, “Aerodynamic models for Darrieus type straight-bladed vertical axis wind turbine,” Renewable and Sustainable Energy Review, 12(4), 1087-1109, 2008.
33 M. Zheng, M.C. Mulenga, G.T. Reader, M. Wang, D.S-K. Ting, J. Tjong, “Biodiesel engine performance and emissions in low temperature combustion,” Fuel, 87(6): 714-722, 2008.
32 W.W. Yang, A. Fartaj, D.S-K. Ting, “Exergy analysis of the advanced transcritical CO2 air conditioning cycles,” International Journal of Exergy, 5(2): 150-163, 2008.
31 M. Islam, D.S-K. Ting, A. Fartaj, “Design of a special-purpose airfoil for smaller-capacity straight-bladed VAWT,” Wind Engineering, 31(6): 401-424, 2007.
30 Z. Faruquee, D.S-K. Ting, A. Fartaj, R. M. Barron, R. Carriveau, “The effects of axis ratio on laminar fluid flow around an elliptical cylinder,” International Journal of Heat and Fluid Flow, 28: 1178-1189, 2007.
29 R. Liu, D.S-K. Ting, “Turbulent flow downstream of a perforated plate: sharp-edged orifice versus finite-thickness holes,” Journal of Fluids Engineering, 129: 1164-1171, 2007.
28 M. Islam, D.S-K. Ting, A. Fartaj, “Desirable airfoil properties for smaller-scale straight-bladed VAWT,” Wind Engineering, 31(3): 165-196, 2007.
27 R. Liu, D.S-K. Ting, M.D. Checkel, “Constant Reynolds number turbulence downstream of an orificed, perforated plate,” Experimental Thermal and Fluid Science, 31: 897-908, 2007.
26 M. Islam, D.S-K. Ting, A. Fartaj, “Assessment of small-capacity straight-bladed VAWT for sustainable development of Canada,” International Journal of Environmental Studies, 64(4): 489-500, 2007.
25 C. Sak, R. Liu, D.S-K. Ting, G.W. Rankin, “The role of turbulence length scale and turbulence intensity on forced convection from a heated horizontal circular cylinder,” Experimental Thermal and Fluid Science, 31: 279-289, 2007.
24 H. Tyagi, R. Liu, D.S-K. Ting, C.R. Johnston, “Measurement of wake properties of a sphere in freestream turbulence,” Experimental Thermal and Fluid Science, 30: 587-604, 2006.
23 M. Zheng, G.T. Reader, D. Wang, J. Zuo, R. Kumar, M.C. Mulenga, U. Asad, D.S-K. Ting, M. Wang, “A thermal response analysis on the transient performance of active diesel aftertreatment,” SAE 2005 Transactions - Journal of Fuels and Lubricants, 1804-1815, 2005 (Paper 2005-01-3885).
22 P.F. Henshaw, T. D’Andrea, K.R.C. Mann, D.S-K. Ting, “Premixed ammonia-methane-air combustion,” Combustion Science and Technology, 177: 2151-2170, 2005.
21 M.G. Khan, A. Fartaj, D.S-K. Ting, “Study of cross-flow cooling and heating of air via elliptical tube array,” Article 4781, ASHRAE Transactions Vol. 111, Part 1: 423-433, 2005.
20 D.S-K. Ting, G.T. Reader, “Hydrogen peroxide for improving premixed methane-air combustion,” Energy, 30: 313-322, 2005.
19 R. Kumar, M. Zheng, G.T. Reader, S.J. Ko, D.S-K. Ting, “Preliminary energy efficiency analysis of an EGR fuel-reformer,” SAE 2004 Transactions - Journal of Fuels and Lubricants, 4: 1667-1675, 2004 (SAE Paper 2004-01-2918).
18 M. Islam, A. Fartaj, D.S-K. Ting, “Current utilization and future prospects of emerging renewable energy applications in Canada,” Renewable and Sustainable Energy Review, 8(6): 493-519, 2004.
17 T. D’Andrea, P.F. Henshaw, D.S-K. Ting, “The addition of hydrogen to a gasoline-fueled SI engine,” International Journal of Hydrogen Energy, 29(14): 1541-1552, 2004.
16 M.G. Khan, A. Fartaj, D.S-K. Ting, “An experimental characterization of cross-flow cooling of air via an in-line elliptical tube array,” International Journal of Heat and Fluid Flow, 25(4): 636-648, 2004.
15 A. Fartaj, D.S-K. Ting, W.W. Yang, “Second law analysis of the transcritical CO2 refrigeration cycle,” Energy Conversion and Management, 45: 2269-2281, 2004.
14 R. Liu, D.S-K. Ting, G.W. Rankin, “On the generation of turbulence with a perforated plate,” Experimental Thermal and Fluid Science, 28: 307-316, 2004.
13 T. D’Andrea, P.F. Henshaw, D.S-K. Ting, A. Sobiesiak, “Investigating combustion enhancement and emissions reduction with the addition of 2H2 + O2 to a SI engine,” SAE 2003 Transactions - Journal of Engines, 112: 1974-1984, 2003 (SAE Paper 2003-32-0011).
12 R. Liu, D.S-K. Ting, M.D. Checkel, “Combustion hazard of mixing ammonia with nitric oxide,” Journal of Loss Prevention in the Process Industries, 16(6): 497-506, 2003.
11 D.S-K. Ting, C. Uykur, “A chemical kinetics study on oxygen-enriched CO/H2/air flames,” Energy Sources, 24(6): 513-529, 2002.
10 D.S-K. Ting, M.D. Checkel, “The effect of mean turbulent strain rate on the flame speed of premixed, growing flames,” ASME Journal of Engineering for Gas Turbine and Power, 123(1): 175-181, 2001.
9 C. Uykur, P.F. Henshaw, D.S-K. Ting, R.M. Barron, “Effects of addition of electrolysis products on methane/air premixed laminar combustion,” International Journal of Hydrogen Energy, 26(3): 265-273, 2001.
8 D.S-K. Ting, D.J. Wang, S.J. Price, M.P. Païdoussis, “An experimental study on the fluid elastic forces for two staggered circular cylinders in cross-flow,” Journal of Fluids and Structures, 12: 259-294, 1998.
7 D.S-K. Ting, M.D. Checkel, “The importance of turbulence intensity, eddy size and flame size in spark ignited, premixed flame growth,” Proceedings of the Institution of Mechanical Engineers, Part D, Journal of Automobile Engineering, 211: 83-86, 1997.
6 D.S-K. Ting, “Temperature fluctuations measurements for transitional flow in a square channel,” Experimental Heat Transfer, 9: 357-370, 1996.
5 D.S-K. Ting, K.C. Cheng, “Relaminarization of developing turbulent flow in a 180o curved square channel: a study based on temperature fluctuation measurements,” Experimental Heat Transfer, 9: 267-285, 1996.
4 K.C. Cheng, D.S-K. Ting, “Note on thermocouple measurements for laminar-turbulent transition phenomena in pipe flow,” Experimental Heat Transfer, 8: 209-228, 1995.
3 M.D. Checkel, D.S-K. Ting, W.K. Bushe, “Flammability limits and burning velocity of ammonia / nitric oxide mixtures,” Journal of Loss Prevention in the Process Industries, 8(4): 215-220, 1995.
2 W.T. Ashurst, M.D. Checkel, D.S-K. Ting, “The eddy structure model of turbulent flamelet propagation, the expanding spherical and steady planar cases,” Combustion Science and Technology, 99: 51-74, 1994.
1 M.D. Checkel, D.S-K. Ting, “Turbulence effects on developing turbulent flames in a constant volume combustion chamber,” SAE Transactions - Journal of Engines, 102: 1216-1226, 1993 (SAE Paper 930867).
89 K. Bassett, R. Carriveau, D.S-K. Ting, “Experimental analysis of buoyancy battery energy storage system,” Renewable Power Generation, DOI: 10.1049/iet-rpg.2016.0033 , Online ISSN 1752-1424 Available online: 23 September 2016.
88 Z. Wang, W. Xiong, D.S-K. Ting, R. Carriveau, Z. Wang, “Conventional and advanced exergy analyses of an underwater compressed air energy storage system,” Applied Energy, 180: 810-822, 2016.
87 D. C. J. Rice, R. Carriveau, D.S-K Ting, “Commercial greenhouse water demand sensitivity analysis: single crop case study,” Water Science and Technology: Water Supply, 16(3): DOI: 10.2166/ws.2016.031, 13 pages, 2016.
86 S. Alhasan, R. Carriveau, D.S-K. Ting, “A review of adsorbed natural gas storage technologies,” Journal of Environmental Studies, 73(3): 343-356, 2016.
85 M. Ahmadi-Baloutaki, R. Carriveau, D.S-K. Ting, “A wind tunnel study on the aerodynamic interaction of vertical axis wind turbines in array configurations,” Renewable Energy, 96(A): 904-913, 2016.
84 A. Raeesi, S. Cheng, D.S-K. Ting, “Application of a three-dimensional aeroelastic model to study the wind-induced response of bridge stay cables under unsteady wind conditions,” Journal of Sound and Vibration, 375: 217-236, 2016.
83 Z. Wang, D.S-K. Ting, R. Carriveau, W. Xiong, Z. Wang, “Design and thermodynamic analysis of a multi-level underwater compressed air energy storage system,” Journal of Energy Storage, 5: 203-211, 2016.
82 H. Cen, R. Carriveau, D.S-K. Ting, “Effect of mass ratio on the hydrodynamic response of a flexible cylinder,” Journal of Marine Science and Application, 15(1): 50-62, 2016.
81 F. Fouladi, P. Henshaw, D.S-K. Ting, “Effect of a triangular rib on a flat plate boundary layer,” Journal of Fluids Engineering, 138(1), 011101:1-11, 2016.
80 A.R. Vasel-Be-Hagh, R. Carriveau, D.S-K. Ting, J.S Turner, “On the drag of buoyant vortex rings,” Physical Review E, 92:043024, 1-6, DOI: 10.1103/PhysRevE.92.043024, 2015.
79 K. Bassett, R. Carriveau, D.S-K. Ting,“3D printed wind turbines Part 1: Design considerations and rapid manufacture potential,” Sustainable Energy Technologies and Assessments, 11:186-193, 2015.
78 M. Ahmadi-Baloutaki, R. Carriveau, D.S-K. Ting, “Performance of a vertical axis wind turbine in grid turbulence,” Sustainable Energy Technologies and Assessments, 11: 178-185, 2015.
77 H. Cen, M. Ahmadi-Baloutaki, D.S-K. Ting, R. Carriveau, “Mitigating flow-induced vibration of a flexible circular cylinder via pre-tension,” Sustainable Energy Technologies and Assessments, 11:173-177, 2015.
76 A.R. Vasel-Be-Hagh, R. Carriveau, D.S-K. Ting, “Structural analysis of an underwater energy storage accumulator,” Sustainable Energy Technologies and Assessments, 11:165-172, 2015.
75 C.G. Cvetkovski, S. Reitsma, T. Bolisetti, D.S-K. Ting, “Heat transfer in a U-bend pipe: Dean number versus Reynolds number,” Sustainable Energy Technologies and Assessments, 11:148-158, 2015.
74 M. Ahmadi-Baloutaki, R. Carriveau, D.S-K. Ting, “An experimental study on the interaction between free-stream turbulence and a wing-tip vortex in the near-field,” Aerospace Science and Technology, 43: 395-405, 2015.
73 U. Asad, M. Zheng, D.S-K. Ting, J. Tjong, “Implementation challenges and solutions for homogeneous charge compression ignition combustion in diesel engines,” Journal of Engineering for Gas Turbines and Power, 137/101505, 9 pages, 2015.
72 A.R. Vasel-Be-Hagh, R. Carriveau, D.S-K. Ting, “A balloon bursting underwater,” Journal of Fluid Mechanics, 769: 522-540, 2015.
71 J. Smith, R. Carriveau, D.S-K. Ting, “Turbine power production sensitivity to coastal sheared and turbulent inflows,” Wind Engineering, 39(2): 183-192, 2015.
70 A.R. Vasel-Be-Hagh, R. Carriveau, D. S-K. Ting, “Flow over submerged energy storage balloons in closely and widely spaced floral configurations,” Ocean Engineering, 95(1): 59-77, 2015.
69 F. Fouladi, P. Henshaw, D.S-K. Ting, “Turbulent flow over a flat plate downstream of a finite height perforated plate,” Journal of Fluids Engineering, 127(2): 021203, 12 pages, 2015.
68 G. Martínez-Narro, P.F. Henshaw, D.S-K. Ting, “Mexico’s shoreline as a site for the transition to renewable energy,” International Journal of Environmental Studies, 71(6): 877-886, 2014.
67 I. Arianmehr, D.S-K. Ting, S. Ray, “Effect of a transverse groove on cooling of a surrogate photovoltaic panel,” International Journal of Environmental Studies, 71(6): 850-861, 2014.
66 C.G. Cvetkovski, S. Reitsma, T. Bolisetti, D.S-K. Ting, “Ground source heat pumps: should we use single U-bend or coaxial ground exchanger loops?,” International Journal of Environmental Studies, 71(6): 828-839, 2014.
65 A.R. Vasel-Be-Hagh, R. Carriveau, D.S-K. Ting, “Flow past an accumulator unit of an underwater energy storage system: three touching balloons in a floral configuration,” Journal of Marine Science and Application, 13: 467-476, 2014.
64 J. Smith, R. Carriveau, D.S-K. Ting, “Inflow parameter effects on wind turbine tower cyclic loading,” Wind Engineering, 38(5): 477-488, 2014.
63 B.C. Cheung, R. Carriveau, D.S-K. Ting, “Parameters affecting scalable underwater compressed air energy storage,” Applied Energy, 134: 239-247, 2014.
62 B.C. Cheung, R. Carriveau, D.S-K. Ting, “Multi-objective optimization of an underwater compressed air energy storage system using a genetic algorithm,” Energy, 74: 396-404, 2014.
61 M. Ahmadi-Baloutaki, R. Carriveau, D.S-K. Ting, “Straight-bladed vertical axis wind turbine rotor design guide based on aerodynamic performance and loading analysis,” Proceeding of Institution of Mechanical Engineers, Part A: Journal Power & Energy, 228(7): 742-759, 2014 (one of two winners of the SAGE Best Paper Prize in 2014 by the editorial board of Journal of Power and Energy).
60 P. McKay, R. Carriveau, D.S-K. Ting, J. Jehrendt, “Global sensitivity analysis of wind turbine power output,” Wind Energy, 17(7): 983-995, 2014.
59 A. Raeesi, S. Cheng, D.S-K. Ting, “A two-degree-of-freedom aeroelastic model for the vibration of dry cylindrical body along unsteady air flow and its application to aerodynamic response of dry inclined cables,” Journal of Wind Engineering and Industrial Aerodynamics, 130: 108-124, 2014.
58 A. R. Vasel-Be-Hagh, R. Carriveau, D. S-K. Ting, “Underwater compressed air energy storage improved through vortex hydro energy,” Sustainable Energy Technologies and Assessments, 7: 1-5, 2014.
57 J. Aman, D. S-K. Ting, P. Henshaw, “Residential solar air conditioning: energy and exergy analysis of an ammonia-water absorption cooling system,” Applied Thermal Energy, 62: 424-432, 2014.
56 A.R. Vasel-Be-Hagh, R. Carriveau, D.S-K. Ting, “Energy storage using weights hydraulically lifted above ground,” International Journal of Environmental Studies, 70(5): 792-799, 2013.
55 F. Fouladi, P. Henshaw, D.S-K. Ting, “Enhancing smart grid realization with accurate prediction of photovoltaic performance based on weather forecast,” International Journal of Environmental Studies, 70(5): 754-764, 2013.
54 M. Ahmadi-Baloutaki, R. Carriveau, D.S-K. Ting, “Effect of free-stream turbulence on flow characteristics over a transversely-grooved surface,” Experimental Thermal and Fluid Science, 51: 56-70, 2013.
53 A.R. Vasel-Be-Hagh, R. Carriveau, D. S-K. Ting, “Numerical simulation of flow past an underwater energy storage balloon,” Computers and Fluids, 88: 272-286, 2013.
52 M. Ahmadi-Baloutaki, D.S-K. Ting, R. Carriveau, “The role of free-stream turbulence on flow evolution in the wake of a VAWT blade,” Wind Engineering, 37(4): 401-420, 2013.
51 A.R. Vasel-Be-Hagh, D.S-K. Ting, R. Carriveau,“Correlating flow pattern with force coefficients in air flow past a tandem unit of three circular cylinders,” International Journal of Fluid Mechanics Research, 40(3): 1-19, 2013.
50 A. Raeesi, S. Cheng, D.S-K. Ting, “Aerodynamic damping of an inclined circular cylinder in unsteady flow and its application to the prediction of dry inclined cable galloping,” Journal of Wind Engineering and Industrial Aerodynamics, 113: 12-28, 2013.
49 P. McKay, R. Carriveau, D.S-K. Ting, “Wake impacts on downstream wind turbine performance and yaw alignment,” Wind Energy, 16: 221-234, 2013.
48 N. Younis, D.S-K. Ting, “The subtle effect of integral scale on the drag of a circular cylinder in turbulent cross flow,” Wind and Structures, 15(6): 463-480, 2012.
47 B. Cheung, N. Cao, R. Carriveau, D.S-K. Ting, “Distensible air accumulators as a means of adiabatic underwater compressed air energy storage,” International Journal of Environmental Studies, 69(4): 566-577, 2012.
46 J. Bas, J. Smith, R. Carriveau, S. Cheng, D.S-K. Ting, T. Newson, “Structural response of a commercial wind turbine to various stopping events,” Wind Engineering, 36(5): 553-569, 2012.
45 J. Konrad, R. Carriveau, M. Davison, F. Simpson, D.S-K. Ting, “Geological compressed air energy storage as an enabling technology for renewable energy in Ontario, Canada,” International Journal of Environmental Studies, 69(2): 350-359, 2012.
44 A. Raeesi, S. Cheng, D.S-K. Ting, “Some insight into the wind-induced vibration of stay cables in the context of rigid static inclined circular cylinder,” Journal of Applied Fluid Mechanics, 5(2): 99-112, 2012.
43 N. Cao, D.S-K. Ting, R. Carriveau, “Correlating a high-lift airfoil performance with turbulence strain rate,” Wind Engineering, 35(5): 589-606, 2011.
42 K. Bassett, R. Carriveau, D.S-K. Ting, “Vibration response of a 2.3 MW wind turbine to yaw motion and shut down events,” Wind Energy, 14(8): 939-952, 2011.
41 P. McKay, R. Carriveau, D.S-K. Ting, “Farm wide dynamics: the next critical wind energy frontier,” Wind Engineering, 35(4): 397-418, 2011.
40 N. Cao, D.S-K. Ting, R. Carriveau, “The performance of a high-lift airfoil in turbulent wind,” Wind Engineering, 35(2): 179-196, 2011.
39 N. Moradian, D.S-K. Ting, S. Cheng, “Advancing drag crisis of a sphere via the manipulation of integral length scale,” Wind and Structures, 14(1): 35-53, 2011.
38 K. Bassett, R. Carriveau, D.S-K. Ting, “Vibration analysis of 2.3 MW wind turbine operation using the discrete wavelet transform,” Wind Engineering, 34(4): 375-388, 2010.
37 M. Younis, T. Bolisetti, D.S-K. Ting, “Ground source heat pump systems: current status,” International Journal of Environmental Studies, 67(3): 405-415, 2010.
36 N. Moradian, D.S-K. Ting, S. Cheng, “The effects of freestream turbulence on the drag coefficient of a sphere,” Experimental Thermal and Fluid Science, 33: 460-471, 2009.
35 A. Raeesi, S. Cheng, D.S-K. Ting, “Spatial flow structure around a smooth circular cylinder in the critical Reynolds number regime under cross-flow condition,” Wind and Structures, 11(3): 221-240, 2008.
34 M. Islam, D.S-K. Ting, A. Fartaj, “Aerodynamic models for Darrieus type straight-bladed vertical axis wind turbine,” Renewable and Sustainable Energy Review, 12(4), 1087-1109, 2008.
33 M. Zheng, M.C. Mulenga, G.T. Reader, M. Wang, D.S-K. Ting, J. Tjong, “Biodiesel engine performance and emissions in low temperature combustion,” Fuel, 87(6): 714-722, 2008.
32 W.W. Yang, A. Fartaj, D.S-K. Ting, “Exergy analysis of the advanced transcritical CO2 air conditioning cycles,” International Journal of Exergy, 5(2): 150-163, 2008.
31 M. Islam, D.S-K. Ting, A. Fartaj, “Design of a special-purpose airfoil for smaller-capacity straight-bladed VAWT,” Wind Engineering, 31(6): 401-424, 2007.
30 Z. Faruquee, D.S-K. Ting, A. Fartaj, R. M. Barron, R. Carriveau, “The effects of axis ratio on laminar fluid flow around an elliptical cylinder,” International Journal of Heat and Fluid Flow, 28: 1178-1189, 2007.
29 R. Liu, D.S-K. Ting, “Turbulent flow downstream of a perforated plate: sharp-edged orifice versus finite-thickness holes,” Journal of Fluids Engineering, 129: 1164-1171, 2007.
28 M. Islam, D.S-K. Ting, A. Fartaj, “Desirable airfoil properties for smaller-scale straight-bladed VAWT,” Wind Engineering, 31(3): 165-196, 2007.
27 R. Liu, D.S-K. Ting, M.D. Checkel, “Constant Reynolds number turbulence downstream of an orificed, perforated plate,” Experimental Thermal and Fluid Science, 31: 897-908, 2007.
26 M. Islam, D.S-K. Ting, A. Fartaj, “Assessment of small-capacity straight-bladed VAWT for sustainable development of Canada,” International Journal of Environmental Studies, 64(4): 489-500, 2007.
25 C. Sak, R. Liu, D.S-K. Ting, G.W. Rankin, “The role of turbulence length scale and turbulence intensity on forced convection from a heated horizontal circular cylinder,” Experimental Thermal and Fluid Science, 31: 279-289, 2007.
24 H. Tyagi, R. Liu, D.S-K. Ting, C.R. Johnston, “Measurement of wake properties of a sphere in freestream turbulence,” Experimental Thermal and Fluid Science, 30: 587-604, 2006.
23 M. Zheng, G.T. Reader, D. Wang, J. Zuo, R. Kumar, M.C. Mulenga, U. Asad, D.S-K. Ting, M. Wang, “A thermal response analysis on the transient performance of active diesel aftertreatment,” SAE 2005 Transactions - Journal of Fuels and Lubricants, 1804-1815, 2005 (Paper 2005-01-3885).
22 P.F. Henshaw, T. D’Andrea, K.R.C. Mann, D.S-K. Ting, “Premixed ammonia-methane-air combustion,” Combustion Science and Technology, 177: 2151-2170, 2005.
21 M.G. Khan, A. Fartaj, D.S-K. Ting, “Study of cross-flow cooling and heating of air via elliptical tube array,” Article 4781, ASHRAE Transactions Vol. 111, Part 1: 423-433, 2005.
20 D.S-K. Ting, G.T. Reader, “Hydrogen peroxide for improving premixed methane-air combustion,” Energy, 30: 313-322, 2005.
19 R. Kumar, M. Zheng, G.T. Reader, S.J. Ko, D.S-K. Ting, “Preliminary energy efficiency analysis of an EGR fuel-reformer,” SAE 2004 Transactions - Journal of Fuels and Lubricants, 4: 1667-1675, 2004 (SAE Paper 2004-01-2918).
18 M. Islam, A. Fartaj, D.S-K. Ting, “Current utilization and future prospects of emerging renewable energy applications in Canada,” Renewable and Sustainable Energy Review, 8(6): 493-519, 2004.
17 T. D’Andrea, P.F. Henshaw, D.S-K. Ting, “The addition of hydrogen to a gasoline-fueled SI engine,” International Journal of Hydrogen Energy, 29(14): 1541-1552, 2004.
16 M.G. Khan, A. Fartaj, D.S-K. Ting, “An experimental characterization of cross-flow cooling of air via an in-line elliptical tube array,” International Journal of Heat and Fluid Flow, 25(4): 636-648, 2004.
15 A. Fartaj, D.S-K. Ting, W.W. Yang, “Second law analysis of the transcritical CO2 refrigeration cycle,” Energy Conversion and Management, 45: 2269-2281, 2004.
14 R. Liu, D.S-K. Ting, G.W. Rankin, “On the generation of turbulence with a perforated plate,” Experimental Thermal and Fluid Science, 28: 307-316, 2004.
13 T. D’Andrea, P.F. Henshaw, D.S-K. Ting, A. Sobiesiak, “Investigating combustion enhancement and emissions reduction with the addition of 2H2 + O2 to a SI engine,” SAE 2003 Transactions - Journal of Engines, 112: 1974-1984, 2003 (SAE Paper 2003-32-0011).
12 R. Liu, D.S-K. Ting, M.D. Checkel, “Combustion hazard of mixing ammonia with nitric oxide,” Journal of Loss Prevention in the Process Industries, 16(6): 497-506, 2003.
11 D.S-K. Ting, C. Uykur, “A chemical kinetics study on oxygen-enriched CO/H2/air flames,” Energy Sources, 24(6): 513-529, 2002.
10 D.S-K. Ting, M.D. Checkel, “The effect of mean turbulent strain rate on the flame speed of premixed, growing flames,” ASME Journal of Engineering for Gas Turbine and Power, 123(1): 175-181, 2001.
9 C. Uykur, P.F. Henshaw, D.S-K. Ting, R.M. Barron, “Effects of addition of electrolysis products on methane/air premixed laminar combustion,” International Journal of Hydrogen Energy, 26(3): 265-273, 2001.
8 D.S-K. Ting, D.J. Wang, S.J. Price, M.P. Païdoussis, “An experimental study on the fluid elastic forces for two staggered circular cylinders in cross-flow,” Journal of Fluids and Structures, 12: 259-294, 1998.
7 D.S-K. Ting, M.D. Checkel, “The importance of turbulence intensity, eddy size and flame size in spark ignited, premixed flame growth,” Proceedings of the Institution of Mechanical Engineers, Part D, Journal of Automobile Engineering, 211: 83-86, 1997.
6 D.S-K. Ting, “Temperature fluctuations measurements for transitional flow in a square channel,” Experimental Heat Transfer, 9: 357-370, 1996.
5 D.S-K. Ting, K.C. Cheng, “Relaminarization of developing turbulent flow in a 180o curved square channel: a study based on temperature fluctuation measurements,” Experimental Heat Transfer, 9: 267-285, 1996.
4 K.C. Cheng, D.S-K. Ting, “Note on thermocouple measurements for laminar-turbulent transition phenomena in pipe flow,” Experimental Heat Transfer, 8: 209-228, 1995.
3 M.D. Checkel, D.S-K. Ting, W.K. Bushe, “Flammability limits and burning velocity of ammonia / nitric oxide mixtures,” Journal of Loss Prevention in the Process Industries, 8(4): 215-220, 1995.
2 W.T. Ashurst, M.D. Checkel, D.S-K. Ting, “The eddy structure model of turbulent flamelet propagation, the expanding spherical and steady planar cases,” Combustion Science and Technology, 99: 51-74, 1994.
1 M.D. Checkel, D.S-K. Ting, “Turbulence effects on developing turbulent flames in a constant volume combustion chamber,” SAE Transactions - Journal of Engines, 102: 1216-1226, 1993 (SAE Paper 930867).
Books/Book Chapters:
10 Methane and Hydrogen for Energy Storage, Editors: R. Carriveau & D.S-K. Ting, The Institute of Engineering and Technology, London, UK, ISBN: 978-1-78561-193-3, 176 pages, 2016.
9 “Chapter 8: Gas Hydrate Potential and Development for Methane Storage,” A. Goyal, J. Stagner, D.S-K. Ting in Methane and Hydrogen for Energy Storage, Editors: R. Carriveau & D.S-K. Ting, The Institute of Engineering and Technology, London, UK, 2016.
8 “Chapter 7: Thermal Management as a Key in Storing Adsorbed Natural Gas,” M. Ahmadi-Baloutaki, R. Carriveau, D.S-K. Ting in Methane and Hydrogen for Energy Storage, Editors: R. Carriveau & D.S-K. Ting, The Institute of Engineering and Technology, London, UK, 2016.
7 D.S-K. Ting, Basics of Engineering Turbulence, Academic Press, ISBN: 978-0-12-803970-0, 234 pages, 2016.
6 D.S-K. Ting, Some Basics of Engineering Flow Turbulence: Revised Edition, ISBN: 978-0-9869355-3-4, Naomi Ting’s Books, 292 pages, 2013.
5 D.S-K. Ting, Some Basics of Engineering Combustion, ISBN: 978-0-9869355-2-7, Naomi Ting’s Books, 244 pages, 2012.
4 P. McKay, R. Carriveau, D.S-K. Ting, T. Newson, ‘Chapter X: Turbine Wake Dynamics’ (20 pages) in Advances in Wind Power edited by R. Carriveau, ISBN 980-953-307-535-3, InTech Publishing, 2012.
3 D.S-K. Ting, ‘Chapter 6: Some Unique Roles of Turbulent Scales in Engineering’ (28 pages) in Turbulence: Theory, Types and Simulation edited by R.J. Marcuso, ISBN: 978-1-61761-735-5, Nova Science Publishers, 2011.
2 D.S-K. Ting, Some Basics of Engineering Flow Turbulence, ISBN: 978-0-9869355-1-0, Naomi Ting’s Books, 251 pages, 2011.
1 D.S-K. Ting, An Introduction to Combustion Engineering, ISBN: 978-0-9869355-0-3, Naomi Ting’s Books, 206 pages, 2011.
9 “Chapter 8: Gas Hydrate Potential and Development for Methane Storage,” A. Goyal, J. Stagner, D.S-K. Ting in Methane and Hydrogen for Energy Storage, Editors: R. Carriveau & D.S-K. Ting, The Institute of Engineering and Technology, London, UK, 2016.
8 “Chapter 7: Thermal Management as a Key in Storing Adsorbed Natural Gas,” M. Ahmadi-Baloutaki, R. Carriveau, D.S-K. Ting in Methane and Hydrogen for Energy Storage, Editors: R. Carriveau & D.S-K. Ting, The Institute of Engineering and Technology, London, UK, 2016.
7 D.S-K. Ting, Basics of Engineering Turbulence, Academic Press, ISBN: 978-0-12-803970-0, 234 pages, 2016.
6 D.S-K. Ting, Some Basics of Engineering Flow Turbulence: Revised Edition, ISBN: 978-0-9869355-3-4, Naomi Ting’s Books, 292 pages, 2013.
5 D.S-K. Ting, Some Basics of Engineering Combustion, ISBN: 978-0-9869355-2-7, Naomi Ting’s Books, 244 pages, 2012.
4 P. McKay, R. Carriveau, D.S-K. Ting, T. Newson, ‘Chapter X: Turbine Wake Dynamics’ (20 pages) in Advances in Wind Power edited by R. Carriveau, ISBN 980-953-307-535-3, InTech Publishing, 2012.
3 D.S-K. Ting, ‘Chapter 6: Some Unique Roles of Turbulent Scales in Engineering’ (28 pages) in Turbulence: Theory, Types and Simulation edited by R.J. Marcuso, ISBN: 978-1-61761-735-5, Nova Science Publishers, 2011.
2 D.S-K. Ting, Some Basics of Engineering Flow Turbulence, ISBN: 978-0-9869355-1-0, Naomi Ting’s Books, 251 pages, 2011.
1 D.S-K. Ting, An Introduction to Combustion Engineering, ISBN: 978-0-9869355-0-3, Naomi Ting’s Books, 206 pages, 2011.
Books/Journals Edited:
9 D.S-K. Ting, Member of the Editorial Board of Sustainable Energy Technologies and Assessments, Elsevier, 2012-present.
8 R. Carriveau, D.S-K. Ting, Methane and Hydrogen for Energy Storage, 8 chapters, The Institute of Engineering and Technology, London, UK, ISBN: 978-1-78561-193-3, 176 pages, 2016.
7 Monograph on Natural Gas and Energy Storage, International Journal of Environmental Studies, Guest Editors: R. Carriveau, D.S-K. Ting, 73(3), 2016.
6 Special Issue on Offshore Energy and Storage, Sustainable Energy Technologies and Assessments, Guest Editors: R. Carriveau, D.S-K. Ting, Volume 11, 2015.
5 Special Issue on Turbulent Energy, International Journal of Environmental Studies, Guest Editors: R. Carriveau, D.S-K. Ting, 71(6): 785-786, 2014.
4 Monograph on Renewable Energies and Smart Grid – The Solution for Tomorrow’s Energy, International Journal of Environmental Studies, Guest Editors: R. Carriveau, D.S-K. Ting, 70(5), 2013.
3 Monograph on Energy Conservation, Generation and Storage, International Journal of Environmental Studies, Guest Editors: D.S-K. Ting, K.Y. Fung, 69(2), 2012.
2 Special Canadian Issue on Energy Conversion and the Environment, International Journal of Environmental Studies, Guest Editors: D.S-K. Ting, K.Y. Fung, 64(4), 2007.
1 Special Issue on Automotive Power and Environment in Canada, International Journal of Environmental Studies, Guest Editors: D.S-K. Ting, K.Y. Fung, 63(4), 2006.
8 R. Carriveau, D.S-K. Ting, Methane and Hydrogen for Energy Storage, 8 chapters, The Institute of Engineering and Technology, London, UK, ISBN: 978-1-78561-193-3, 176 pages, 2016.
7 Monograph on Natural Gas and Energy Storage, International Journal of Environmental Studies, Guest Editors: R. Carriveau, D.S-K. Ting, 73(3), 2016.
6 Special Issue on Offshore Energy and Storage, Sustainable Energy Technologies and Assessments, Guest Editors: R. Carriveau, D.S-K. Ting, Volume 11, 2015.
5 Special Issue on Turbulent Energy, International Journal of Environmental Studies, Guest Editors: R. Carriveau, D.S-K. Ting, 71(6): 785-786, 2014.
4 Monograph on Renewable Energies and Smart Grid – The Solution for Tomorrow’s Energy, International Journal of Environmental Studies, Guest Editors: R. Carriveau, D.S-K. Ting, 70(5), 2013.
3 Monograph on Energy Conservation, Generation and Storage, International Journal of Environmental Studies, Guest Editors: D.S-K. Ting, K.Y. Fung, 69(2), 2012.
2 Special Canadian Issue on Energy Conversion and the Environment, International Journal of Environmental Studies, Guest Editors: D.S-K. Ting, K.Y. Fung, 64(4), 2007.
1 Special Issue on Automotive Power and Environment in Canada, International Journal of Environmental Studies, Guest Editors: D.S-K. Ting, K.Y. Fung, 63(4), 2006.
Book Reviews:
9 D.S-K. Ting, “‘Green Illusions - The Dirty Secrets of Clean Energy and the Future of Environmentalism,’ by O. Zehner, University of Nebraska Press, 2012” International Journal of Environmental Studies, 70(5): 612-615, 2013.
8 D.S-K. Ting, “‘Heat Islands – Understanding and Mitigating Heat in Urban Areas,’ by L. Gartland, Earthscan, London, 2011” International Journal of Environmental Studies, 69(6): 1008-1011, 2012.
7 D.S-K. Ting, “‘Materials for Energy Efficiency and Thermal Comfort in Buildings,’ edited by M.R. Hall, Woodhead Energy Series No. 14, CRC Press, Taylor & Francis Group, 2010,” International Journal of Environmental Studies, 68(6): 983-993, 2011.
6 D.S-K. Ting, “‘Geothermal Energy: Renewable Energy and the Environment,’ by W.E. Glassley, CRC Press, Taylor & Francis Group, 2010,” International Journal of Environmental Studies, 68(2): 229-234, 2011.
5 D.S-K. Ting, “‘The Dynamics of Energy: Supply, Conversion, and Utilization,’ by H. Perez-Blanco, CRC Press, Taylor & Francis Group, 2009,” International Journal of Environmental Studies, 67(6): 959-961, 2010.
4 D.S-K. Ting, “‘Low-Enthalpy Geothermal Resources for Power Generation,’ by D. Chandrasekharam and J. Bundschuh, Routledge, 2008,” International Journal of Environmental Studies, 67(4): 621-622, 2010.
3 D.S-K. Ting, “‘WHO Handbook on Indoor Radon: A Public Health Perspective’, by World Health Organization, 2009,” International Journal of Environmental Studies, 67(1): 100-102, 2010.
2 D.S-K. Ting, “‘Ventilation and Airflow in Buildings: Methods for Diagnosis and Evaluation’ by Claude-Alain Roulet, Earthscan, London and Sterling, VA, 2008,” International Journal of Environmental Studies, 65(4): 627-628, 2008.
1 D.S-K. Ting, “‘China Shifts Gears: Automakers, Oil, Pollution and Development’ by Kelly Sims Gallagher, MIT Press, Cambridge, 2006,” International Journal of Environmental Studies, 64(2): 283-284, 2007.
9 D.S-K. Ting, “‘Green Illusions - The Dirty Secrets of Clean Energy and the Future of Environmentalism,’ by O. Zehner, University of Nebraska Press, 2012” International Journal of Environmental Studies, 70(5): 612-615, 2013.
8 D.S-K. Ting, “‘Heat Islands – Understanding and Mitigating Heat in Urban Areas,’ by L. Gartland, Earthscan, London, 2011” International Journal of Environmental Studies, 69(6): 1008-1011, 2012.
7 D.S-K. Ting, “‘Materials for Energy Efficiency and Thermal Comfort in Buildings,’ edited by M.R. Hall, Woodhead Energy Series No. 14, CRC Press, Taylor & Francis Group, 2010,” International Journal of Environmental Studies, 68(6): 983-993, 2011.
6 D.S-K. Ting, “‘Geothermal Energy: Renewable Energy and the Environment,’ by W.E. Glassley, CRC Press, Taylor & Francis Group, 2010,” International Journal of Environmental Studies, 68(2): 229-234, 2011.
5 D.S-K. Ting, “‘The Dynamics of Energy: Supply, Conversion, and Utilization,’ by H. Perez-Blanco, CRC Press, Taylor & Francis Group, 2009,” International Journal of Environmental Studies, 67(6): 959-961, 2010.
4 D.S-K. Ting, “‘Low-Enthalpy Geothermal Resources for Power Generation,’ by D. Chandrasekharam and J. Bundschuh, Routledge, 2008,” International Journal of Environmental Studies, 67(4): 621-622, 2010.
3 D.S-K. Ting, “‘WHO Handbook on Indoor Radon: A Public Health Perspective’, by World Health Organization, 2009,” International Journal of Environmental Studies, 67(1): 100-102, 2010.
2 D.S-K. Ting, “‘Ventilation and Airflow in Buildings: Methods for Diagnosis and Evaluation’ by Claude-Alain Roulet, Earthscan, London and Sterling, VA, 2008,” International Journal of Environmental Studies, 65(4): 627-628, 2008.
1 D.S-K. Ting, “‘China Shifts Gears: Automakers, Oil, Pollution and Development’ by Kelly Sims Gallagher, MIT Press, Cambridge, 2006,” International Journal of Environmental Studies, 64(2): 283-284, 2007.
Refereed Conference Papers:
58 J. Liu, J. Jaekel, D. Ramdani, N. Khan, D.S-K. Ting, M.J. Ahamed, “Effect of geometric and material properties on thermoelastic damping (TED) of 3D hemispherical inertial resonator,” Proceedings of ASME 2016 International Mechanical Engineering Congress & Exposition, Paper IMECE2016-66277, 7 pages, November 11-17, 2016, Phoenix, Arizona, USA.
57 J. Aman, P. Henshaw, D.S-K. Ting, “Modeling and analysis of bubble pump parameters for vapor absorption refrigeration systems,” 2016 ASHRAE Annual Conference, Paper #19256, 8 pages, June 25 - 29, 2016, St. Louis, Missouri, USA.
56 P. Divekar, Z. Yang, D. Ting, X. Chen, M. Zheng, J. Tjong, “Efficiency and emission trade-off in diesel-ethanol low temperature combustion cycles,” SAE 2015 World Congress, SAE Technical Paper 2015-01-0845, 12 pages, April 21-23, 2015, Detroit, Michigan, USA.
55 F. Iakovidis, D.S-K. Ting, “Effect of free stream turbulence on air cooling of a surrogate PV panel,” Proceedings of the ASME 2014 International Mechanical Engineering Congress & Exposition, Paper IMECE2014-36560, 10 pages, November 14-20, 2014, Montreal, Canada.
54 M. Ahmadi-Baloutaki, R. Carriveau, D.S-K. Ting, “Frequency analysis of a trailing vortex flow subjected to external turbulence,” Proceedings of the ASME 2014 International Mechanical Engineering Congress & Exposition, Paper IMECE2014-37699, 10 pages, November 14-20, 2014, Montreal, Canada.
53 F. Fouladi, P. Henshaw, D.S-K. Ting, “Wavelet analysis of finite height grid turbulence over a flat plate,” Proceedings of the ASME 2014 International Mechanical Engineering Congress & Exposition, Paper IMECE2014-36803, 9 pages, November 14-20, 2014, Montreal, Canada.
52 H. Cen, D.S-K. Ting, R. Carriveau, “On cross flow-induced vibration of a flexible cylinder,” Proceedings of the ASME 2014 International Mechanical Engineering Congress & Exposition, Paper IMECE2014-38642, 8 pages, November 14-20, 2014, Montreal, Canada.
51 U. Asad, M. Zheng, D. Ting, J. Tjong, “Implementation challenges and solutions for homogeneous charge compression ignition combustion in diesel engines,”Proceedings of the ASME 2014 Internal Combustion Engine Division Fall Technical Conference, Paper ICEF2014-5413, 13 pages, October 19-22, 2014, Columbus, IN, USA.
50 M. Ahmadi-Baloutaki, R. Carriveau, D.S-K. Ting, “Design criteria on sizing and material selection of SB-VAWTs,” Proceedings of the ASME 2013 International Mechanical Engineering Congress & Exposition, Paper IMECE2013-63367, 9 pages, November 13-21, 2013, San Diego, California, USA.
49 I. Arianmehr, D.S-K. Ting, S. Ray, “Assisted turbulence convective heat transfer for cooling the photovoltaic cells,” Proceedings of the ASME 2013 Summer Heat Transfer Conference, Paper HT2013-17210, doi:10.1115/HT2013-17210, 10 pages, July 14-19, 2013, Minneapolis, MN, USA.
48 C.G. Cvetkovski, H.S. Mozaffari, S. Reitsma, T. Bolisetti, D.S-K. Ting, “On fluid flow and heat transfer in a pipe with a U-bend,” Proceedings of the ASME 2013 Summer Heat Transfer Conference, Paper HT2013-17209, 10 pages, July 14-19, 2013, Minneapolis, MN, USA.
47 S. Cheng, A. Raeesi, D.S-K. Ting, “Advances in the understanding of wind-induced cable vibration phenomena in the subcritical and critical Reynolds number regimes,” Proceedings of 2011 CSCE Annual General Meeting and Conference, Ottawa, Canada, (invited), pp. 979-989, June 2011.
46 K. Bassett, R. Carriveau, D.S-K. Ting, “Passive structural health monitoring applied to a wind turbine model,” ASME 3rd Annual Conference on Energy Sustainability, July 19-23, 2009, San Francisco, Paper 90178, 5 pages.
45 M. Islam, M.R. Amin, D.S-K. Ting, A. Fartaj, “Selection of airfoils for straight-bladed vertical axis wind turbines based on desirable aerodynamic characteristics,” ASME International Mechanical Engineering Congress and Exposition (IMECE) 2008, Boston, Massachusetts, Oct 31-Nov 6, 2008, Paper IMECE2008-66027, 8 pages.
44 M. Zheng, U. Asad, G.T. Reader, X. Han, M. Pournazeri, D.S-K. Ting, M. Wang, “Diesel EGR fuel reformer improvement with flow reversal and central fueling,” 2008 SAE International Powertrains, Fuels and Lubricants Congress, June 23-25, 2008, Shanghai, China, SAE Paper 2008-01-1607, 12 pages.
43 D. Yang, S. Cheng, D.S-K. Ting, “Wind tunnel study on the “wake bubble” of model truck,” 2008 SAE International Congress & Exposition, Paper 2008-01-0739, 8 pages.
42 M. Islam, M.R. Amin, D.S-K. Ting, A. Fartaj, “Performance analysis of a smaller-capacity straight-bladed VAWT with prospective airfoils,” Paper AIAA-2008-1333, 46th AIAA Aerospace Sciences Meeting and Exhibit, January 7-10, Reno, Navada, 2008, 17 pages.
41 M. Islam, M.R. Amin, D.S-K. Ting, A. Fartaj, “Aerodynamic factors affecting performance of straight-bladed vertical axis wind turbines,” ASME International Mechanical Engineering Congress and Exposition, November 10-16, Seattle, Washington, 2007, 10 pages.
40 M. Zheng, U. Asad, G.T. Reader, D.S-K. Ting, “A preliminary response analysis of exhaust pipe plenums for diesel aftertreatment improvement,” SAE 2006 Powertrain & Fluid Systems Conference & Exhibition, Paper 2006-01-3310, 12 pages.
39 M. Zheng, M.C. Mulenga, G.T. Reader, M. Wang, D.S-K. Ting, “Influence of biodiesel fuel on diesel engine performance and emissions in low temperature combustion,” SAE 2006 Powertrain & Fluid Systems Conference & Exhibition, Paper 2006-01-3281, 15 pages.
38 Z. Faruquee, R. Carriveau, D.S-K. Ting, S. Cheng, “Prospects and challenges of wind energy - a Canadian perspective,” IGEC-2, The Second International Green Energy Conference, Paper IGEC-115, 12 pages, 2006.
37 W.W. Yang, A. Fartaj, D.S-K. Ting, “Comparative study of transcritical CO2 and conventional HFC-134a automotive A/C systems,” IGEC-2, The Second International Green Energy Conference, Paper IGEC-078, 12 pages, 2006.
36 W.W. Yang, A. Fartaj, D.S-K. Ting, “Exergy analysis of the advanced transcritical CO2 air conditioning cycles,” IGEC-2, The Second International Green Energy Conference, Paper IGEC-077, 10 pages, 2006.
35 A. De, D.S-K. Ting, M.D. Checkel, “The effects of temperature and pressure on stretched, freely propagating, premixed laminar methane-air flame,” 2006 SAE International Congress & Exposition, Paper 2006-01-0494, 19 pages.
34 U. Asad, M. Zheng, D.S-K. Ting, G.T. Reader, “Effect of internal exhaust gas recycling on n-heptane HCCI combustion,” ASME ICE 2005 Fall Technical Conference, Paper No. ICEF2005-1245, 2005, 11 pages.
33 Z. Faruquee, D.S-K. Ting, A. Fartaj, “Confinement effects on air cross-flow over an elliptical cylinder,” 2005 ASME Fluids Engineering Summer Conference, Paper FEDSM2005-77100, 10 pages.
32 H. Tyagi, R. Liu, D.S-K. Ting, C.R. Johnson, “Experimental study of vortex shedding from a solid sphere in turbulent freestream,” 2005 ASME Fluids Engineering Summer Conference, Paper FEDSM2005-77168, 9 pages.
31 R. Liu, D.S-K. Ting, R. Carriveau, “Energy transfer in nearly isotropic perforated-plate turbulence,” 2005 ASME Fluids Engineering Summer Conference, Paper FEDSM2005-77124, 9 pages.
30 W.W. Yang, A. Fartaj, D.S-K. Ting, “CO2 automotive A/C system optimum high pressure control,” 2005 SAE Vehicle Thermal Management Systems, Paper 2005-01-2022, 10 pages.
29 F. Sun, X. Chen, D.S-K. Ting, A. Sobiesiak, “Control-oriented model of isooctane HCCI combustion,” 16th International Federation of Automatic Control (IFAC) World Congress, Praha, Czech Republic, July 4-8, 2005, Paper 04807, 6 pages.
28 F. Sun, X. Chen, D.S-K. Ting, A. Sobiesiak, “Model for operation of HCCI engines fueled with ethanol,” 24th American Control Conference, ACC 2005, Portland, Oregon, June 8-10, Paper 0182_WeB14_3, Proceeding of American Control Conference, pp. 1003-1009.
27 B. Emami, R. Liu, D.S-K. Ting, M.D. Checkel, “A numerical study on the burning velocity of a spherical, premixed methane-air flame,” 2005 SAE International Congress & Exposition, Paper 2005-01-1124, 9 pages.
26 H. Tyagi, D.S-K. Ting, “A note on premixed flame-turbulence interactions,” 2005 SAE International Congress & Exposition, Paper 2005-01-0241, 13 pages.
25 B. Emami, R. Liu, D.S-K. Ting, M.D. Checkel, “Rapid distortion of homogeneous turbulence between cylinders,” 2004 ASME International Mechanical Engineering Congress, Paper IMECE2004-60125, 7 pages.
24 H. Tyagi, R. Liu, D.S-K. Ting, C.R. Johnston, “Experimental investigation of perforated plate turbulent flow past a solid sphere,” 2004 ASME International Mechanical Engineering Congress, Paper IMECE2004-60340, 9 pages.
23 M.G. Khan, A. Fartaj, D.S-K. Ting, “An elliptical tube array as a crossflow heat exchanger,”2004 SAE International Congress & Exposition, Paper 2004-01-0217, 10 pages.
22 R. Liu, D.S-K. Ting, M.D. Checkel, “Ammonia as a fuel for SI engine,” SAE 2003 Powertrain & Fluid Systems Conference & Exhibition, Paper 2003-01-3095, 7 pages.
21 M.C. Mulenga, D.S-K. Ting, G.T. Reader, M. Zheng, “The potential for reducing CO and NOx emissions from an HCCI engine using H2O2 addition,” SAE 2003 Powertrain & Fluid Systems Conference & Exhibition, Paper 2003-01-3204, 13 pages.
20 M.C. Mulenga, G.T. Reader, D.S-K. Ting, M. Zheng, “Prospect of reduced CO and NOx emissions in diesel dual fuel engines,” ASME ICE Fall 2003 Technical Conference, Paper ICEF2003-768, 9 pages.
19 R. Liu, D.S-K. Ting, “On the aerodynamics of wind turbines,” ASME FACT, International Joint Power Generation Conference & Exposition 2003, Paper IJPGC2003-40137, 7 pages.
18 M.C. Mulenga, D.S-K. Ting, G.T. Reader, M. Zheng, “Effect of hydrogen peroxide on premixed iso-octane/air combustion,” ASME FACT, International Joint Power Generation Conference & Exposition 2003, Paper IJPGC2003-40108, 9 pages.
17 R. Liu, D.S-K. Ting, M.D. Checkel, “Characteristics of ammonia-nitric oxide combustion,” ASME FACT, International Joint Power Generation Conference & Exposition 2003, Paper IJPGC2003-40111, 7 pages.
16 C. Sak, R. Liu, D.S-K. Ting, G.W. Rankin, “The effect of turbulence on forced convection from a heated horizontal circular cylinder,” 6th ASME-JSME Thermal Engineering Joint Conference, C5 Experimental Measurements of Turbulent Heat Transfer: Paper 315, 7 pages, 2003.
15 R. Liu, A. Fartaj, D.S-K. Ting, “An experimental study on cross-flow cooling via an elliptical tube array,” 6th ASME-JSME Thermal Engineering Joint Conference, B5 Heat Exchangers: Paper 176, 7 pages, 2003.
14 A. Sobiesiak, C. Uykur, D.S-K. Ting, P.F. Henshaw, “Hydrogen/oxygen additives influence on premixed iso-octane/air flame,” SAE 2002 Spring Fuels & Lubricants Conference & Exhibition, Paper 2002-01-1710.
13 D.S-K. Ting, G.T. Reader, “Hydrogen peroxide for improving premixed methane-air combustion,” 3rd International Symposium on Advanced Energy Conversion Systems and Related Technologies, pp. 156-162, Nagoya, Japan, December 15-17, 2001.
12 C. Uykur, A.L. Zuccato, G.T. Reader, D.S-K. Ting, “Hydrogen peroxide effect on HCCI performance,” ASME ICE 2001 Fall Technical Conference, Paper No. 2001-ICE-417, ICE-Vol. 37-2, 97-105, 2001.
11 P.F. Henshaw, K.R.C. Mann, C. Uykur, D.S-K. Ting, “Premixed ammonia-methane-air combustion,” ASME FACT, International Joint Power Generation Conference & Exposition 2001, 7 pages.
10 C. Uykur, W.T. Paun, D.S-K. Ting, “Hydrogen/oxygen addition on premixed methane/air flames,” ASME FACT, International Joint Power Generation Conference & Exposition 2001, 9 pages.
9 C. Uykur, A. Sobiesiak, P.F. Henshaw, D.S-K. Ting, “Effects of addition of electrolysis products on iso-octane premixed laminar combustion,” ASME FACT, International Joint Power Generation Conference & Exposition 2001, 8 pages.
8 K.R.C. Mann, D.S-K. Ting, P.F. Henshaw, “A semi-empirical model of spark-ignited turbulent premixed flame growth,” SAE 2000 International Congress, Paper 2000-01-0201, 15 pages.
7 D.S-K. Ting, M.D. Checkel, “The effect of mean turbulent strain rate on the flame speed of premixed, growing flames,” ASME ICE 1999 Fall Technical Conference, Paper No. 99-ICE-242, ICE-Vol. 33-3, 67-74, 1999.
6 D.S-K. Ting, D.J. Wang, S.J. Price, M.P. Païdoussis, “The applicability of the quasi-steady assumption for two staggered circular cylinders in cross-flow,” ASME: Proceedings of 4th International Symposium on Fluid-Structure Interactions, Aeroelasticity, Flow-Induced Vibration & Noise, Vol. 53-1: 159-168, 1997.
5 K.C. Cheng, D.S-K. Ting, “Laminar-turbulent transition for air flow in a square duct: a study using temperature fluctuations,” Process, enhanced, and multiphase heat transfer. A Festschrift for A.E. Bergles, (editors: R.M. Manglik & A.D. Kraus), pp. 367-377, 1996.
4 D.S-K. Ting, M.D. Checkel, “The effects of turbulence on spark-ignited, ultra lean, premixed methane-air flame growth in a combustion chamber,” 1995 SAE Fuels & Lubricants Meeting & Exposition, Paper 952410, 10 pages.
3 D.S-K. Ting, M.D. Checkel, B. Johansson, “The importance of high-frequency, small-eddy turbulence in spark-ignited, premixed engine combustion,” 1995 SAE Fuels & Lubricants Meeting & Exposition, Paper 952409, 15 pages.
2 D.S-K. Ting, M.D. Checkel, R. Haley, P.R. Smy, “Early flame acceleration measurements in a turbulent spark-ignited mixture,” 1994 SAE International Congress & Exposition, Paper 940687, 17 pages.
1 M.D. Checkel, D.S-K. Ting, “Measuring turbulent flame growth by visualization,” 1992 SAE International Congress & Exposition, Paper 920184, 9 pages.
57 J. Aman, P. Henshaw, D.S-K. Ting, “Modeling and analysis of bubble pump parameters for vapor absorption refrigeration systems,” 2016 ASHRAE Annual Conference, Paper #19256, 8 pages, June 25 - 29, 2016, St. Louis, Missouri, USA.
56 P. Divekar, Z. Yang, D. Ting, X. Chen, M. Zheng, J. Tjong, “Efficiency and emission trade-off in diesel-ethanol low temperature combustion cycles,” SAE 2015 World Congress, SAE Technical Paper 2015-01-0845, 12 pages, April 21-23, 2015, Detroit, Michigan, USA.
55 F. Iakovidis, D.S-K. Ting, “Effect of free stream turbulence on air cooling of a surrogate PV panel,” Proceedings of the ASME 2014 International Mechanical Engineering Congress & Exposition, Paper IMECE2014-36560, 10 pages, November 14-20, 2014, Montreal, Canada.
54 M. Ahmadi-Baloutaki, R. Carriveau, D.S-K. Ting, “Frequency analysis of a trailing vortex flow subjected to external turbulence,” Proceedings of the ASME 2014 International Mechanical Engineering Congress & Exposition, Paper IMECE2014-37699, 10 pages, November 14-20, 2014, Montreal, Canada.
53 F. Fouladi, P. Henshaw, D.S-K. Ting, “Wavelet analysis of finite height grid turbulence over a flat plate,” Proceedings of the ASME 2014 International Mechanical Engineering Congress & Exposition, Paper IMECE2014-36803, 9 pages, November 14-20, 2014, Montreal, Canada.
52 H. Cen, D.S-K. Ting, R. Carriveau, “On cross flow-induced vibration of a flexible cylinder,” Proceedings of the ASME 2014 International Mechanical Engineering Congress & Exposition, Paper IMECE2014-38642, 8 pages, November 14-20, 2014, Montreal, Canada.
51 U. Asad, M. Zheng, D. Ting, J. Tjong, “Implementation challenges and solutions for homogeneous charge compression ignition combustion in diesel engines,”Proceedings of the ASME 2014 Internal Combustion Engine Division Fall Technical Conference, Paper ICEF2014-5413, 13 pages, October 19-22, 2014, Columbus, IN, USA.
50 M. Ahmadi-Baloutaki, R. Carriveau, D.S-K. Ting, “Design criteria on sizing and material selection of SB-VAWTs,” Proceedings of the ASME 2013 International Mechanical Engineering Congress & Exposition, Paper IMECE2013-63367, 9 pages, November 13-21, 2013, San Diego, California, USA.
49 I. Arianmehr, D.S-K. Ting, S. Ray, “Assisted turbulence convective heat transfer for cooling the photovoltaic cells,” Proceedings of the ASME 2013 Summer Heat Transfer Conference, Paper HT2013-17210, doi:10.1115/HT2013-17210, 10 pages, July 14-19, 2013, Minneapolis, MN, USA.
48 C.G. Cvetkovski, H.S. Mozaffari, S. Reitsma, T. Bolisetti, D.S-K. Ting, “On fluid flow and heat transfer in a pipe with a U-bend,” Proceedings of the ASME 2013 Summer Heat Transfer Conference, Paper HT2013-17209, 10 pages, July 14-19, 2013, Minneapolis, MN, USA.
47 S. Cheng, A. Raeesi, D.S-K. Ting, “Advances in the understanding of wind-induced cable vibration phenomena in the subcritical and critical Reynolds number regimes,” Proceedings of 2011 CSCE Annual General Meeting and Conference, Ottawa, Canada, (invited), pp. 979-989, June 2011.
46 K. Bassett, R. Carriveau, D.S-K. Ting, “Passive structural health monitoring applied to a wind turbine model,” ASME 3rd Annual Conference on Energy Sustainability, July 19-23, 2009, San Francisco, Paper 90178, 5 pages.
45 M. Islam, M.R. Amin, D.S-K. Ting, A. Fartaj, “Selection of airfoils for straight-bladed vertical axis wind turbines based on desirable aerodynamic characteristics,” ASME International Mechanical Engineering Congress and Exposition (IMECE) 2008, Boston, Massachusetts, Oct 31-Nov 6, 2008, Paper IMECE2008-66027, 8 pages.
44 M. Zheng, U. Asad, G.T. Reader, X. Han, M. Pournazeri, D.S-K. Ting, M. Wang, “Diesel EGR fuel reformer improvement with flow reversal and central fueling,” 2008 SAE International Powertrains, Fuels and Lubricants Congress, June 23-25, 2008, Shanghai, China, SAE Paper 2008-01-1607, 12 pages.
43 D. Yang, S. Cheng, D.S-K. Ting, “Wind tunnel study on the “wake bubble” of model truck,” 2008 SAE International Congress & Exposition, Paper 2008-01-0739, 8 pages.
42 M. Islam, M.R. Amin, D.S-K. Ting, A. Fartaj, “Performance analysis of a smaller-capacity straight-bladed VAWT with prospective airfoils,” Paper AIAA-2008-1333, 46th AIAA Aerospace Sciences Meeting and Exhibit, January 7-10, Reno, Navada, 2008, 17 pages.
41 M. Islam, M.R. Amin, D.S-K. Ting, A. Fartaj, “Aerodynamic factors affecting performance of straight-bladed vertical axis wind turbines,” ASME International Mechanical Engineering Congress and Exposition, November 10-16, Seattle, Washington, 2007, 10 pages.
40 M. Zheng, U. Asad, G.T. Reader, D.S-K. Ting, “A preliminary response analysis of exhaust pipe plenums for diesel aftertreatment improvement,” SAE 2006 Powertrain & Fluid Systems Conference & Exhibition, Paper 2006-01-3310, 12 pages.
39 M. Zheng, M.C. Mulenga, G.T. Reader, M. Wang, D.S-K. Ting, “Influence of biodiesel fuel on diesel engine performance and emissions in low temperature combustion,” SAE 2006 Powertrain & Fluid Systems Conference & Exhibition, Paper 2006-01-3281, 15 pages.
38 Z. Faruquee, R. Carriveau, D.S-K. Ting, S. Cheng, “Prospects and challenges of wind energy - a Canadian perspective,” IGEC-2, The Second International Green Energy Conference, Paper IGEC-115, 12 pages, 2006.
37 W.W. Yang, A. Fartaj, D.S-K. Ting, “Comparative study of transcritical CO2 and conventional HFC-134a automotive A/C systems,” IGEC-2, The Second International Green Energy Conference, Paper IGEC-078, 12 pages, 2006.
36 W.W. Yang, A. Fartaj, D.S-K. Ting, “Exergy analysis of the advanced transcritical CO2 air conditioning cycles,” IGEC-2, The Second International Green Energy Conference, Paper IGEC-077, 10 pages, 2006.
35 A. De, D.S-K. Ting, M.D. Checkel, “The effects of temperature and pressure on stretched, freely propagating, premixed laminar methane-air flame,” 2006 SAE International Congress & Exposition, Paper 2006-01-0494, 19 pages.
34 U. Asad, M. Zheng, D.S-K. Ting, G.T. Reader, “Effect of internal exhaust gas recycling on n-heptane HCCI combustion,” ASME ICE 2005 Fall Technical Conference, Paper No. ICEF2005-1245, 2005, 11 pages.
33 Z. Faruquee, D.S-K. Ting, A. Fartaj, “Confinement effects on air cross-flow over an elliptical cylinder,” 2005 ASME Fluids Engineering Summer Conference, Paper FEDSM2005-77100, 10 pages.
32 H. Tyagi, R. Liu, D.S-K. Ting, C.R. Johnson, “Experimental study of vortex shedding from a solid sphere in turbulent freestream,” 2005 ASME Fluids Engineering Summer Conference, Paper FEDSM2005-77168, 9 pages.
31 R. Liu, D.S-K. Ting, R. Carriveau, “Energy transfer in nearly isotropic perforated-plate turbulence,” 2005 ASME Fluids Engineering Summer Conference, Paper FEDSM2005-77124, 9 pages.
30 W.W. Yang, A. Fartaj, D.S-K. Ting, “CO2 automotive A/C system optimum high pressure control,” 2005 SAE Vehicle Thermal Management Systems, Paper 2005-01-2022, 10 pages.
29 F. Sun, X. Chen, D.S-K. Ting, A. Sobiesiak, “Control-oriented model of isooctane HCCI combustion,” 16th International Federation of Automatic Control (IFAC) World Congress, Praha, Czech Republic, July 4-8, 2005, Paper 04807, 6 pages.
28 F. Sun, X. Chen, D.S-K. Ting, A. Sobiesiak, “Model for operation of HCCI engines fueled with ethanol,” 24th American Control Conference, ACC 2005, Portland, Oregon, June 8-10, Paper 0182_WeB14_3, Proceeding of American Control Conference, pp. 1003-1009.
27 B. Emami, R. Liu, D.S-K. Ting, M.D. Checkel, “A numerical study on the burning velocity of a spherical, premixed methane-air flame,” 2005 SAE International Congress & Exposition, Paper 2005-01-1124, 9 pages.
26 H. Tyagi, D.S-K. Ting, “A note on premixed flame-turbulence interactions,” 2005 SAE International Congress & Exposition, Paper 2005-01-0241, 13 pages.
25 B. Emami, R. Liu, D.S-K. Ting, M.D. Checkel, “Rapid distortion of homogeneous turbulence between cylinders,” 2004 ASME International Mechanical Engineering Congress, Paper IMECE2004-60125, 7 pages.
24 H. Tyagi, R. Liu, D.S-K. Ting, C.R. Johnston, “Experimental investigation of perforated plate turbulent flow past a solid sphere,” 2004 ASME International Mechanical Engineering Congress, Paper IMECE2004-60340, 9 pages.
23 M.G. Khan, A. Fartaj, D.S-K. Ting, “An elliptical tube array as a crossflow heat exchanger,”2004 SAE International Congress & Exposition, Paper 2004-01-0217, 10 pages.
22 R. Liu, D.S-K. Ting, M.D. Checkel, “Ammonia as a fuel for SI engine,” SAE 2003 Powertrain & Fluid Systems Conference & Exhibition, Paper 2003-01-3095, 7 pages.
21 M.C. Mulenga, D.S-K. Ting, G.T. Reader, M. Zheng, “The potential for reducing CO and NOx emissions from an HCCI engine using H2O2 addition,” SAE 2003 Powertrain & Fluid Systems Conference & Exhibition, Paper 2003-01-3204, 13 pages.
20 M.C. Mulenga, G.T. Reader, D.S-K. Ting, M. Zheng, “Prospect of reduced CO and NOx emissions in diesel dual fuel engines,” ASME ICE Fall 2003 Technical Conference, Paper ICEF2003-768, 9 pages.
19 R. Liu, D.S-K. Ting, “On the aerodynamics of wind turbines,” ASME FACT, International Joint Power Generation Conference & Exposition 2003, Paper IJPGC2003-40137, 7 pages.
18 M.C. Mulenga, D.S-K. Ting, G.T. Reader, M. Zheng, “Effect of hydrogen peroxide on premixed iso-octane/air combustion,” ASME FACT, International Joint Power Generation Conference & Exposition 2003, Paper IJPGC2003-40108, 9 pages.
17 R. Liu, D.S-K. Ting, M.D. Checkel, “Characteristics of ammonia-nitric oxide combustion,” ASME FACT, International Joint Power Generation Conference & Exposition 2003, Paper IJPGC2003-40111, 7 pages.
16 C. Sak, R. Liu, D.S-K. Ting, G.W. Rankin, “The effect of turbulence on forced convection from a heated horizontal circular cylinder,” 6th ASME-JSME Thermal Engineering Joint Conference, C5 Experimental Measurements of Turbulent Heat Transfer: Paper 315, 7 pages, 2003.
15 R. Liu, A. Fartaj, D.S-K. Ting, “An experimental study on cross-flow cooling via an elliptical tube array,” 6th ASME-JSME Thermal Engineering Joint Conference, B5 Heat Exchangers: Paper 176, 7 pages, 2003.
14 A. Sobiesiak, C. Uykur, D.S-K. Ting, P.F. Henshaw, “Hydrogen/oxygen additives influence on premixed iso-octane/air flame,” SAE 2002 Spring Fuels & Lubricants Conference & Exhibition, Paper 2002-01-1710.
13 D.S-K. Ting, G.T. Reader, “Hydrogen peroxide for improving premixed methane-air combustion,” 3rd International Symposium on Advanced Energy Conversion Systems and Related Technologies, pp. 156-162, Nagoya, Japan, December 15-17, 2001.
12 C. Uykur, A.L. Zuccato, G.T. Reader, D.S-K. Ting, “Hydrogen peroxide effect on HCCI performance,” ASME ICE 2001 Fall Technical Conference, Paper No. 2001-ICE-417, ICE-Vol. 37-2, 97-105, 2001.
11 P.F. Henshaw, K.R.C. Mann, C. Uykur, D.S-K. Ting, “Premixed ammonia-methane-air combustion,” ASME FACT, International Joint Power Generation Conference & Exposition 2001, 7 pages.
10 C. Uykur, W.T. Paun, D.S-K. Ting, “Hydrogen/oxygen addition on premixed methane/air flames,” ASME FACT, International Joint Power Generation Conference & Exposition 2001, 9 pages.
9 C. Uykur, A. Sobiesiak, P.F. Henshaw, D.S-K. Ting, “Effects of addition of electrolysis products on iso-octane premixed laminar combustion,” ASME FACT, International Joint Power Generation Conference & Exposition 2001, 8 pages.
8 K.R.C. Mann, D.S-K. Ting, P.F. Henshaw, “A semi-empirical model of spark-ignited turbulent premixed flame growth,” SAE 2000 International Congress, Paper 2000-01-0201, 15 pages.
7 D.S-K. Ting, M.D. Checkel, “The effect of mean turbulent strain rate on the flame speed of premixed, growing flames,” ASME ICE 1999 Fall Technical Conference, Paper No. 99-ICE-242, ICE-Vol. 33-3, 67-74, 1999.
6 D.S-K. Ting, D.J. Wang, S.J. Price, M.P. Païdoussis, “The applicability of the quasi-steady assumption for two staggered circular cylinders in cross-flow,” ASME: Proceedings of 4th International Symposium on Fluid-Structure Interactions, Aeroelasticity, Flow-Induced Vibration & Noise, Vol. 53-1: 159-168, 1997.
5 K.C. Cheng, D.S-K. Ting, “Laminar-turbulent transition for air flow in a square duct: a study using temperature fluctuations,” Process, enhanced, and multiphase heat transfer. A Festschrift for A.E. Bergles, (editors: R.M. Manglik & A.D. Kraus), pp. 367-377, 1996.
4 D.S-K. Ting, M.D. Checkel, “The effects of turbulence on spark-ignited, ultra lean, premixed methane-air flame growth in a combustion chamber,” 1995 SAE Fuels & Lubricants Meeting & Exposition, Paper 952410, 10 pages.
3 D.S-K. Ting, M.D. Checkel, B. Johansson, “The importance of high-frequency, small-eddy turbulence in spark-ignited, premixed engine combustion,” 1995 SAE Fuels & Lubricants Meeting & Exposition, Paper 952409, 15 pages.
2 D.S-K. Ting, M.D. Checkel, R. Haley, P.R. Smy, “Early flame acceleration measurements in a turbulent spark-ignited mixture,” 1994 SAE International Congress & Exposition, Paper 940687, 17 pages.
1 M.D. Checkel, D.S-K. Ting, “Measuring turbulent flame growth by visualization,” 1992 SAE International Congress & Exposition, Paper 920184, 9 pages.
Articles in Professional Journals/Magazines/Bulletins:
5 B. Cheung, R. Carriveau, D.S-K. Ting “Storing energy underwater,” Mechanical Engineering– the Magazine of ASME, 134(12): 38-41, 2012.
4 D.S-K. Ting “Comment on Lance Williams’ ‘Importance of Double-blind Reviews’,” Letter to the Editor, Physics Today, 61 (8): 15, 2008.
3 R. Liu, D.S-K. Ting, M.D. Checkel, “Combustion characteristics of ammonia-nitric oxide mixture,” Energy-Tech, http://www.energy-tech.com, pp. 9-18, April 2003.
2 D.S-K. Ting, M.D. Checkel, “TECHNICAL UPDATE: Turbulence in combustion engines,” CSME Bulletin, pp. 4-5, May 1994.
1 W.T. Ashurst, M.D. Checkel, D.S-K. Ting, “A new model of turbulent flame propagation,” CRF News, Volume 15, No. 6, November/December 1993, Combustion Research Facility, Sandia National Laboratories, USA, 1993.
4 D.S-K. Ting “Comment on Lance Williams’ ‘Importance of Double-blind Reviews’,” Letter to the Editor, Physics Today, 61 (8): 15, 2008.
3 R. Liu, D.S-K. Ting, M.D. Checkel, “Combustion characteristics of ammonia-nitric oxide mixture,” Energy-Tech, http://www.energy-tech.com, pp. 9-18, April 2003.
2 D.S-K. Ting, M.D. Checkel, “TECHNICAL UPDATE: Turbulence in combustion engines,” CSME Bulletin, pp. 4-5, May 1994.
1 W.T. Ashurst, M.D. Checkel, D.S-K. Ting, “A new model of turbulent flame propagation,” CRF News, Volume 15, No. 6, November/December 1993, Combustion Research Facility, Sandia National Laboratories, USA, 1993.
Abstracts/Short Papers Presented/Published in Conference Proceedings:
65 A. Raeesi, S. Cheng, D.S-K. Ting, “Predicting galloping of an elliptical cylinder using a non-linear quasi-steady model,” 8th International Colloquium on Bluff Body Aerodynamics and Applications, Boston, Massachusetts, USA, June 7-11, 2016, 8 pages.
64 A. Ahmed, H. Wu, F. Fouladi, D.S-K. Ting, “The effect of partial-grid turbulence on the blowout velocity of a candle flame,” 2016 Spring Technical Meeting, The Combustion Institute, Canadian Section, 6 pages.
63 K. Bassett, R. Carriveau, D.S-K. Ting, “Experimental analysis of buoyancy battery under water energy storage,” Proceedings of 2015 Offshore Energy & Storage Symposium, Edinburgh, United Kingdom, UWCAES Society, July 1-3, 2015, 7 pages.
62 T. Baert, P. McKay, R. Carriveau, D. Ting, R. Kent, “Windtelligence: the development of a wind farm performance management system,” North American Wind Energy Academy 2015 Symposium, Blacksburg, Virginia, June 9-11, 2015.
61 F. Fouladi, P. Henshaw, D.S-K. Ting, “Turbulent flow behind a partially blocking grid,” the 26th Canadian Congress of Applied Mechanics, Paper #87, 4 pages CANCAM 2015, London, Canada, May 31-June 4, 2015.
60 D. Gordon, T. Bolisetti, S. Reitsma, D.S-K. Ting, “Analytical approaches to modelling temperature variations for a vertical ground-coupled heat pump system,” Geothermal Energy, Paper H12A-06 (abstract + presentation), AGU Joint Assembly, Montreal, Canada, 3-7 May, 2015.
59 V.R. Melanathuru, T. Bolisetti, S. Reitsma, D.S-K. Ting, “Numerical simulation of deep bore heat pumps,” Geothermal Energy, Paper H12A-03 (abstract + presentation), AGU Joint Assembly, Montreal, Canada, 3-7 May, 2015.
58 A. Vasel-Be-Hagh, R. Carriveau, D.S-K. Ting, “Flow induced vibrations of an underwater energy storage accumulator,” Proceedings of 2014 Offshore Energy & Storage Symposium, Windsor, Ontario, Canada, UWCAES Society, July 10-11, 2014, 7 pages.
57 G. Martinez-Narro, D.S.-K. Ting, P. Henshaw, “From oil to renewable: the potential of Mexico shoreline,” Proceedings of 2014 Offshore Energy & Storage Symposium, Windsor, Ontario, Canada, UWCAES Society, July 10-11, 2014, 7 pages.
56 H. Cen, M. Ahmadi-Baloutaki, D.S-K. Ting, R. Carriveau, “Effects of pre-tension on flow-induced vibration of a flexible circular cylinder subjected to uniform cross flow,” Proceedings of 2014 Offshore Energy & Storage Symposium, Windsor, Ontario, Canada, UWCAES Society, July 10-11, 2014, 6 pages.
55 M. Jeftic, Z. Yang, D.S-K. Ting, M. Zheng, “An investigation of the optimal post injection timing for diesel engine exhaust after-treatment,” 2014 Spring Technical Meeting, The Combustion Institute, Canadian Section, 6 pages.
54 A. Raeesi, S. Cheng, D.S-K. Ting, “Identification of galloping condition for inclined stay cables in steady and unsteady wind,” the 10th International Symposium on Cable Dynamics (ISCD 2014), Copenhagen, Denmark, September 2014.
53 A. Raeesi, S. Cheng, D.S-K. Ting, “Prediction of Inclined Cable Galloping Using a 2DOF Aeroelastic Model,” 7th International Conference on Bridge Maintenance, Safety and Management (IABMA), Paper 0572P, Shanghai, China, July 7-11, 2014.
52 A. Vasel-Be-Hagh, R. Carriveau, D.S-K. Ting, “Flow past an isolated underwater balloon,” the 24th Canadian Congress of Applied Mechanics, CANCAM 2013, 4 pages.
51 J. Smith, J. Bas, R. Carriveau, D.S-K. Ting, S. Cheng, T. Newson, “Atmospheric condition effects on wind turbine tower loading,” AWEA WINDPOWER2013, Chicago Illinois, May 5-8, 2013.
50 P. McKay, J. Smith, J. Bas, R. Carriveau, D.S-K. Ting, S. Cheng, T. Newson, “Atmospheric stability effects on wind turbine tower loading,” American Wind Energy Association, Wind Power Conference & Exhibition, May 5-8, Chicago, IL, 2013.
49 B. Cheung, N. Cao, R. Carriveau, D.S-K. Ting, “Underwater CAES for distributed energy storage in the smart grid,” 2012 IEEE International Conference on Smart Grid Engineering (SGE), Oshawa, Canada, August, 2012, Paper 18, 12 pages.
48 P. McKay, R. Carriveau, D.S-K. Ting, J.L. Johrendt, “Sensitivity of downstream wind turbine output to upstream turbine operation,” American Wind Energy Association, Wind Power Conference & Exhibition, June 3-6, Atlanta, GA, 2012.
47 A. Raeesi, S. Cheng, D.S-K. Ting, “Onset of dry inclined cable galloping in unsteady wind,” the 9th International Symposium on Cable Dynamics (ISCD 2011), Shanghai, China, October 2011.
46 A. Raeesi, S. Cheng, D.S-K. Ting, “Aerodynamic damping of inclined bridge stay cables in unsteady wind,” the 8th International Conference on Structural Dynamics (EuroDyn 2011), Leuven, Belgium, 8 pages, July 2011.
45 B. Motameni, D.S-K. Ting, M.D. Checkel, “Characteristics of ammonia/nitric oxide/air combustion,” 2010 Spring Technical Meeting, The Combustion Institute, Canadian Section, 6 pages.
44 A. Raeesi, S. Cheng, D.S-K. Ting, “Flow separation of a smooth circular cylinder in the critical Reynolds number regime,” Symposium on the Mechanics of Slender Structures 2008, University of Maryland Baltimore County, USA, July 2008, 5 pages.
43 N. Moradian, D.S-K. Ting, S. Cheng, “The role of integral length scale on the drag of a sphere in turbulent freestream,” CSME Forum 2008, 7 pages.
42 P. Zhang, D.S-K. Ting, P.N. Kaloni, “Laminar flamelet modeling of pilot jet methane/air flame: skeletal versus detailed mechanisms,” CSME Forum 2008, 8 pages.
41 P. Ghanbari-Bavarsad, D.S-K. Ting, “Stretched, freely-expanding, laminar, premixed methane/air flame,” CSME Forum 2008, 7 pages.
40 M. Islam, F.U. Ahmed, D.S-K. Ting, A. Fartaj, “Design analysis of fixed-pitch straight-bladed vertical axis wind turbines with an alternative material,” 7th Annual World Wind Energy Conference, June 24-26, Kingston, Ontario, Canada, 2008.
39 T. Olatunji, R. Carriveau, D.S-K. Ting, “An investigation on techniques for hydraulic intake entrainment envelope delineation,” 43rd Central Canadian Symposium on Water Quality Research, February, 2008, 1-page abstract + presentation.
38 N. Moradian, D.S-K. Ting, S. Cheng, “The drag of a sphere in turbulent freestream,” the 21st Canadian Congress of Applied Mechanics, CANCAM 2007, 2 pages.
37 A. Singha, D.S-K. Ting, “On the small scale structures of orificed, perforated plate turbulence,” the 21st Canadian Congress of Applied Mechanics, CANCAM 2007, 2 pages.
36 U. Asad, M. Zheng, D.S-K. Ting, R. Kumar, S. Banerjee, G.T. Reader, J. Tjong, “Real-time heat release analysis towards on-fly combustion control for diesel engines,” 2006 Spring Technical Meeting, The Combustion Institute, Canadian Section, 8 pages.
35 M. C. Mulenga, M. Zheng, G. T. Reader, D.S-K. Ting, Y. Tan, U. Asad, M. Wang, “Investigating EGR on low-temperature combustion NOx and PM in diesel engine,” 2006 Spring Technical Meeting, The Combustion Institute, Canadian Section, 8 pages.
34 A. Singha, D.S-K. Ting, M.D. Checkel, “A simple post-processing approach to modeling in-homogeneous HCCI combustion,” 2006 Spring Technical Meeting, The Combustion Institute, Canadian Section, 6 pages.
33 D.S-K. Ting, A. De, M.D. Checkel, “Stretching of spark-Ignited, freely-propagating, premixed methane-air flame at standard and elevated pressures and temperatures,” 2006 Spring Technical Meeting, The Combustion Institute, Canadian Section, 6 pages.
32 A. Singha, R. Liu, D.S-K. Ting, “Turbulence generation behind orificed, perforated plate,” The American Physical Society 2005 58th Annual Meeting of the Division of Fluid Dynamics, 1-page abstract + oral presentation.
31 H. Tyagi, R. Liu, D.S-K. Ting, “The characteristics of sphere wake in freestream turbulence,” The American Physical Society 2005 58th Annual Meeting of the Division of Fluid Dynamics, 1-page abstract + oral presentation.
30 D.S-K. Ting, “Flame stretching - a premixed example,” International Truck & Engine Corporation / University of Windsor Symposium, October 2005, oral presentation only.
29 D.S-K. Ting, “Some aspects of in-cylinder turbulence,” International Truck & Engine Corporation / University of Windsor Symposium, October 2005, oral presentation only.
28 M. Islam, V. Esfahanian, D.S-K. Ting & A. Fartaj, “Applications of Vertical Axis Wind Turbines for Remote Areas,” 5th Iran National Energy Conference, Tehran, Iran, Spring 2005, 14 pages.
27 W.W. Yang, Y. Wu, A. Fartaj, D.S-K. Ting, “Simulations of carbon dioxide (R-744) and hydrofluorocarbon (R-134a) flowing in a circular tube,” Symposium on Thermo-Fluids Engineering, CSME Forum 2004, 8 pages.
26 R. Liu, D.S-K. Ting, “One, two, and three short, hollow circular cylinders inline downstream of a perforated plate,” Fifth International Colloquium on Bluff Body Aerodynamics & Applications (BBAA V), 4 pages, 2004.
25 B. Emami, R. Liu, D.S-K. Ting, M.D. Checkel, “Turbulence distortion by expanding reaction zones,” 2004 Spring Technical Meeting, The Combustion Institute, Canadian Section, 6 pages.
24 M. Babu, A. Sobiesiak, D.S-K. Ting, “Study of laminar, premixed ethanol/air combustion,” 2004 Spring Technical Meeting, The Combustion Institute, Canadian Section, 6 pages.
23 S-J. Ko, D.S-K. Ting, G.T. Reader, M. Zheng, “Improving engine combustion by hydrogen produced in EGR reformer,”2004 Spring Technical Meeting, The Combustion Institute, Canadian Section, 6 pages.
22 M. Islam, P. Marsh, D.S-K. Ting, A. Fartaj, “Recent developments in vertical axis wind turbines,” 20th Annual Conference and Trade Show of Canadian Wind Energy Association (CanWEA), Montreal, Canada, Oct 17–20, 2004.
21 M. Islam, A. Fartaj, D.S-K. Ting, “Vertical axis wind turbines: past initiatives & future prospects,” the 28th Annual Conference of the Solar Energy Society of Canada, 2003, 13 pages.
20 K. Richters, P.F. Henshaw, D.S-K. Ting, “A study on the effects of hydrogen and oxygen addition to a gasoline spark ignition engine using STANJAN, ESP and CHEMKIN,” 2003 Spring Technical Meeting, The Combustion Institute, Canadian Section, 6 pages.
19 R. Liu, D.S-K. Ting, M.D. Checkel, “Combustion characteristics of ammonia/nitric oxide mixtures,” 2003 Spring Technical Meeting, The Combustion Institute, Canadian Section, 6 pages.
18 R. Liu, D.S-K. Ting, G.W. Rankin, “Turbulence generated using a perforated plate,” 2002 Spring Technical Meeting, The Combustion Institute, Canadian Section, Paper 31, 6 pages.
17 M. Battoei, E. Barbour, S.W. McKellar, D.S-K. Ting, A. Sobiesiak, “Flame inversions in a rectangular duct with 90̊-bend,” 2002 Spring Technical Meeting, The Combustion Institute, Canadian Section, Paper 11, 6 pages.
16 T. D’Andrea, P.F. Henshaw, A. Sobiesiak, D.S-K. Ting, “Hydrogen as a fuel additive to enhance combustion and reduce emissions,” 2002 Spring Technical Meeting, The Combustion Institute, Canadian Section Paper 22, 7 pages.
15 C. Uykur, P.F. Henshaw, A. Sobiesiak, D.S-K. Ting, “Effects of hydrogen/oxygen additives on iso-octane/air combustion,” 17th International Symposium on Combustion Processes, 2001.
14 C. Uykur, P.F. Henshaw, A. Sobiesiak, D.S-K. Ting, “Hydrogen/oxygen additives in premixed iso-octane/air flame,” 2001 Spring Technical Meeting, The Combustion Institute, Canadian Section, Paper 20, 6 pages.
13 C. Uykur, G.T. Reader, D.S-K. Ting, “Hydrogen addition for controlling methane fueled HCCI engine operation,” 2001 Spring Technical Meeting, The Combustion Institute, Canadian Section, Paper 11, 6 pages.
12 K.R.C. Mann, P.F. Henshaw, D.S-K. Ting, “Combustion thermodynamics of ammonia / methane / air mixtures,” 1999 Spring Technical Meeting, The Combustion Institute, Canadian Section, Paper 99-20, 4 pages.
11 M. Ip, D.S-K. Ting, G.W. Rankin, “The effects of piston shape on the performance of a 5.2 L SI engine,” 1998 Spring Technical Meeting, The Combustion Institute, Canadian Section, Paper 5, 5 pages.
10 D.S-K. Ting, M.D. Checkel, “Combustion process in internal combustion engines: the development of spark-ignited, premixed turbulent flames in a combustion chamber,” the Third Asian-Pacific International Symposium on Combustion and Energy Utilization, 6 pages, December 1995.
9 D.S-K. Ting, M.D. Checkel, “The early combustion process in a spark-ignition engine: preference for small-scale turbulence enhancement,” the 15th Canadian Congress of Applied Mechanics, CANCAM 1995, 2 pages.
8 D.S-K. Ting, M.D. Checkel, “Spark-ignited, ultra lean, premixed methane-air flame propagation in a combustion chamber,” 1995 Spring Technical Meeting, The Combustion Institute, Canadian Section, 6 pages.
7 D.S-K. Ting, M.D. Checkel, W.T. Ashurst, “Turbulent burning velocity: dependence upon flame size, flow length scale and velocity intensity,” work-in-progress poster section, The Twenty-Fifth International Symposium on Combustion, August 1994.
6 D.S-K. Ting, M.D. Checkel, “Spark ignited flame propagation in a turbulent flow field,” the Eleventh Canadian Symposium on Fluid Dynamics, 2 pages, June 1994.
5 D.S-K. Ting, M.D. Checkel, “Modelling turbulent flame propagation in a chamber,” 1994 Spring Technical Meeting, The Combustion Institute, Canadian Section, 5 pages.
4 W.T. Ashurst, M.D. Checkel, D.S-K. Ting, “The eddy structure model of turbulent flamelet propagation, the expanding spherical and steady planar cases,” 1993 Fall Technical Meeting, The Combustion Institute, Eastern States Section, USA (Also presented at the Western States Section), Paper 93-060, 30 pages.
3 D.S-K. Ting, M.D. Checkel, “Modelling turbulent flame growth in a combustion chamber,” 1993 Spring Technical Meeting, The Combustion Institute, Canadian Section, Paper 33, 4 pages.
2 M.D. Checkel, D.S-K. Ting, “Turbulence effects on developing flames,” 1992 Spring Technical Meeting, The Combustion Institute, Canadian Section, pp. 22-25.
1 M.D. Checkel, D.S-K. Ting, W.K. Bushe, “Examination of the flammability of ammonia / nitric oxide mixtures,” 1990 Spring Technical Meeting, The Combustion Institute, Canadian and Western States Sections, pp. 143-146.
64 A. Ahmed, H. Wu, F. Fouladi, D.S-K. Ting, “The effect of partial-grid turbulence on the blowout velocity of a candle flame,” 2016 Spring Technical Meeting, The Combustion Institute, Canadian Section, 6 pages.
63 K. Bassett, R. Carriveau, D.S-K. Ting, “Experimental analysis of buoyancy battery under water energy storage,” Proceedings of 2015 Offshore Energy & Storage Symposium, Edinburgh, United Kingdom, UWCAES Society, July 1-3, 2015, 7 pages.
62 T. Baert, P. McKay, R. Carriveau, D. Ting, R. Kent, “Windtelligence: the development of a wind farm performance management system,” North American Wind Energy Academy 2015 Symposium, Blacksburg, Virginia, June 9-11, 2015.
61 F. Fouladi, P. Henshaw, D.S-K. Ting, “Turbulent flow behind a partially blocking grid,” the 26th Canadian Congress of Applied Mechanics, Paper #87, 4 pages CANCAM 2015, London, Canada, May 31-June 4, 2015.
60 D. Gordon, T. Bolisetti, S. Reitsma, D.S-K. Ting, “Analytical approaches to modelling temperature variations for a vertical ground-coupled heat pump system,” Geothermal Energy, Paper H12A-06 (abstract + presentation), AGU Joint Assembly, Montreal, Canada, 3-7 May, 2015.
59 V.R. Melanathuru, T. Bolisetti, S. Reitsma, D.S-K. Ting, “Numerical simulation of deep bore heat pumps,” Geothermal Energy, Paper H12A-03 (abstract + presentation), AGU Joint Assembly, Montreal, Canada, 3-7 May, 2015.
58 A. Vasel-Be-Hagh, R. Carriveau, D.S-K. Ting, “Flow induced vibrations of an underwater energy storage accumulator,” Proceedings of 2014 Offshore Energy & Storage Symposium, Windsor, Ontario, Canada, UWCAES Society, July 10-11, 2014, 7 pages.
57 G. Martinez-Narro, D.S.-K. Ting, P. Henshaw, “From oil to renewable: the potential of Mexico shoreline,” Proceedings of 2014 Offshore Energy & Storage Symposium, Windsor, Ontario, Canada, UWCAES Society, July 10-11, 2014, 7 pages.
56 H. Cen, M. Ahmadi-Baloutaki, D.S-K. Ting, R. Carriveau, “Effects of pre-tension on flow-induced vibration of a flexible circular cylinder subjected to uniform cross flow,” Proceedings of 2014 Offshore Energy & Storage Symposium, Windsor, Ontario, Canada, UWCAES Society, July 10-11, 2014, 6 pages.
55 M. Jeftic, Z. Yang, D.S-K. Ting, M. Zheng, “An investigation of the optimal post injection timing for diesel engine exhaust after-treatment,” 2014 Spring Technical Meeting, The Combustion Institute, Canadian Section, 6 pages.
54 A. Raeesi, S. Cheng, D.S-K. Ting, “Identification of galloping condition for inclined stay cables in steady and unsteady wind,” the 10th International Symposium on Cable Dynamics (ISCD 2014), Copenhagen, Denmark, September 2014.
53 A. Raeesi, S. Cheng, D.S-K. Ting, “Prediction of Inclined Cable Galloping Using a 2DOF Aeroelastic Model,” 7th International Conference on Bridge Maintenance, Safety and Management (IABMA), Paper 0572P, Shanghai, China, July 7-11, 2014.
52 A. Vasel-Be-Hagh, R. Carriveau, D.S-K. Ting, “Flow past an isolated underwater balloon,” the 24th Canadian Congress of Applied Mechanics, CANCAM 2013, 4 pages.
51 J. Smith, J. Bas, R. Carriveau, D.S-K. Ting, S. Cheng, T. Newson, “Atmospheric condition effects on wind turbine tower loading,” AWEA WINDPOWER2013, Chicago Illinois, May 5-8, 2013.
50 P. McKay, J. Smith, J. Bas, R. Carriveau, D.S-K. Ting, S. Cheng, T. Newson, “Atmospheric stability effects on wind turbine tower loading,” American Wind Energy Association, Wind Power Conference & Exhibition, May 5-8, Chicago, IL, 2013.
49 B. Cheung, N. Cao, R. Carriveau, D.S-K. Ting, “Underwater CAES for distributed energy storage in the smart grid,” 2012 IEEE International Conference on Smart Grid Engineering (SGE), Oshawa, Canada, August, 2012, Paper 18, 12 pages.
48 P. McKay, R. Carriveau, D.S-K. Ting, J.L. Johrendt, “Sensitivity of downstream wind turbine output to upstream turbine operation,” American Wind Energy Association, Wind Power Conference & Exhibition, June 3-6, Atlanta, GA, 2012.
47 A. Raeesi, S. Cheng, D.S-K. Ting, “Onset of dry inclined cable galloping in unsteady wind,” the 9th International Symposium on Cable Dynamics (ISCD 2011), Shanghai, China, October 2011.
46 A. Raeesi, S. Cheng, D.S-K. Ting, “Aerodynamic damping of inclined bridge stay cables in unsteady wind,” the 8th International Conference on Structural Dynamics (EuroDyn 2011), Leuven, Belgium, 8 pages, July 2011.
45 B. Motameni, D.S-K. Ting, M.D. Checkel, “Characteristics of ammonia/nitric oxide/air combustion,” 2010 Spring Technical Meeting, The Combustion Institute, Canadian Section, 6 pages.
44 A. Raeesi, S. Cheng, D.S-K. Ting, “Flow separation of a smooth circular cylinder in the critical Reynolds number regime,” Symposium on the Mechanics of Slender Structures 2008, University of Maryland Baltimore County, USA, July 2008, 5 pages.
43 N. Moradian, D.S-K. Ting, S. Cheng, “The role of integral length scale on the drag of a sphere in turbulent freestream,” CSME Forum 2008, 7 pages.
42 P. Zhang, D.S-K. Ting, P.N. Kaloni, “Laminar flamelet modeling of pilot jet methane/air flame: skeletal versus detailed mechanisms,” CSME Forum 2008, 8 pages.
41 P. Ghanbari-Bavarsad, D.S-K. Ting, “Stretched, freely-expanding, laminar, premixed methane/air flame,” CSME Forum 2008, 7 pages.
40 M. Islam, F.U. Ahmed, D.S-K. Ting, A. Fartaj, “Design analysis of fixed-pitch straight-bladed vertical axis wind turbines with an alternative material,” 7th Annual World Wind Energy Conference, June 24-26, Kingston, Ontario, Canada, 2008.
39 T. Olatunji, R. Carriveau, D.S-K. Ting, “An investigation on techniques for hydraulic intake entrainment envelope delineation,” 43rd Central Canadian Symposium on Water Quality Research, February, 2008, 1-page abstract + presentation.
38 N. Moradian, D.S-K. Ting, S. Cheng, “The drag of a sphere in turbulent freestream,” the 21st Canadian Congress of Applied Mechanics, CANCAM 2007, 2 pages.
37 A. Singha, D.S-K. Ting, “On the small scale structures of orificed, perforated plate turbulence,” the 21st Canadian Congress of Applied Mechanics, CANCAM 2007, 2 pages.
36 U. Asad, M. Zheng, D.S-K. Ting, R. Kumar, S. Banerjee, G.T. Reader, J. Tjong, “Real-time heat release analysis towards on-fly combustion control for diesel engines,” 2006 Spring Technical Meeting, The Combustion Institute, Canadian Section, 8 pages.
35 M. C. Mulenga, M. Zheng, G. T. Reader, D.S-K. Ting, Y. Tan, U. Asad, M. Wang, “Investigating EGR on low-temperature combustion NOx and PM in diesel engine,” 2006 Spring Technical Meeting, The Combustion Institute, Canadian Section, 8 pages.
34 A. Singha, D.S-K. Ting, M.D. Checkel, “A simple post-processing approach to modeling in-homogeneous HCCI combustion,” 2006 Spring Technical Meeting, The Combustion Institute, Canadian Section, 6 pages.
33 D.S-K. Ting, A. De, M.D. Checkel, “Stretching of spark-Ignited, freely-propagating, premixed methane-air flame at standard and elevated pressures and temperatures,” 2006 Spring Technical Meeting, The Combustion Institute, Canadian Section, 6 pages.
32 A. Singha, R. Liu, D.S-K. Ting, “Turbulence generation behind orificed, perforated plate,” The American Physical Society 2005 58th Annual Meeting of the Division of Fluid Dynamics, 1-page abstract + oral presentation.
31 H. Tyagi, R. Liu, D.S-K. Ting, “The characteristics of sphere wake in freestream turbulence,” The American Physical Society 2005 58th Annual Meeting of the Division of Fluid Dynamics, 1-page abstract + oral presentation.
30 D.S-K. Ting, “Flame stretching - a premixed example,” International Truck & Engine Corporation / University of Windsor Symposium, October 2005, oral presentation only.
29 D.S-K. Ting, “Some aspects of in-cylinder turbulence,” International Truck & Engine Corporation / University of Windsor Symposium, October 2005, oral presentation only.
28 M. Islam, V. Esfahanian, D.S-K. Ting & A. Fartaj, “Applications of Vertical Axis Wind Turbines for Remote Areas,” 5th Iran National Energy Conference, Tehran, Iran, Spring 2005, 14 pages.
27 W.W. Yang, Y. Wu, A. Fartaj, D.S-K. Ting, “Simulations of carbon dioxide (R-744) and hydrofluorocarbon (R-134a) flowing in a circular tube,” Symposium on Thermo-Fluids Engineering, CSME Forum 2004, 8 pages.
26 R. Liu, D.S-K. Ting, “One, two, and three short, hollow circular cylinders inline downstream of a perforated plate,” Fifth International Colloquium on Bluff Body Aerodynamics & Applications (BBAA V), 4 pages, 2004.
25 B. Emami, R. Liu, D.S-K. Ting, M.D. Checkel, “Turbulence distortion by expanding reaction zones,” 2004 Spring Technical Meeting, The Combustion Institute, Canadian Section, 6 pages.
24 M. Babu, A. Sobiesiak, D.S-K. Ting, “Study of laminar, premixed ethanol/air combustion,” 2004 Spring Technical Meeting, The Combustion Institute, Canadian Section, 6 pages.
23 S-J. Ko, D.S-K. Ting, G.T. Reader, M. Zheng, “Improving engine combustion by hydrogen produced in EGR reformer,”2004 Spring Technical Meeting, The Combustion Institute, Canadian Section, 6 pages.
22 M. Islam, P. Marsh, D.S-K. Ting, A. Fartaj, “Recent developments in vertical axis wind turbines,” 20th Annual Conference and Trade Show of Canadian Wind Energy Association (CanWEA), Montreal, Canada, Oct 17–20, 2004.
21 M. Islam, A. Fartaj, D.S-K. Ting, “Vertical axis wind turbines: past initiatives & future prospects,” the 28th Annual Conference of the Solar Energy Society of Canada, 2003, 13 pages.
20 K. Richters, P.F. Henshaw, D.S-K. Ting, “A study on the effects of hydrogen and oxygen addition to a gasoline spark ignition engine using STANJAN, ESP and CHEMKIN,” 2003 Spring Technical Meeting, The Combustion Institute, Canadian Section, 6 pages.
19 R. Liu, D.S-K. Ting, M.D. Checkel, “Combustion characteristics of ammonia/nitric oxide mixtures,” 2003 Spring Technical Meeting, The Combustion Institute, Canadian Section, 6 pages.
18 R. Liu, D.S-K. Ting, G.W. Rankin, “Turbulence generated using a perforated plate,” 2002 Spring Technical Meeting, The Combustion Institute, Canadian Section, Paper 31, 6 pages.
17 M. Battoei, E. Barbour, S.W. McKellar, D.S-K. Ting, A. Sobiesiak, “Flame inversions in a rectangular duct with 90̊-bend,” 2002 Spring Technical Meeting, The Combustion Institute, Canadian Section, Paper 11, 6 pages.
16 T. D’Andrea, P.F. Henshaw, A. Sobiesiak, D.S-K. Ting, “Hydrogen as a fuel additive to enhance combustion and reduce emissions,” 2002 Spring Technical Meeting, The Combustion Institute, Canadian Section Paper 22, 7 pages.
15 C. Uykur, P.F. Henshaw, A. Sobiesiak, D.S-K. Ting, “Effects of hydrogen/oxygen additives on iso-octane/air combustion,” 17th International Symposium on Combustion Processes, 2001.
14 C. Uykur, P.F. Henshaw, A. Sobiesiak, D.S-K. Ting, “Hydrogen/oxygen additives in premixed iso-octane/air flame,” 2001 Spring Technical Meeting, The Combustion Institute, Canadian Section, Paper 20, 6 pages.
13 C. Uykur, G.T. Reader, D.S-K. Ting, “Hydrogen addition for controlling methane fueled HCCI engine operation,” 2001 Spring Technical Meeting, The Combustion Institute, Canadian Section, Paper 11, 6 pages.
12 K.R.C. Mann, P.F. Henshaw, D.S-K. Ting, “Combustion thermodynamics of ammonia / methane / air mixtures,” 1999 Spring Technical Meeting, The Combustion Institute, Canadian Section, Paper 99-20, 4 pages.
11 M. Ip, D.S-K. Ting, G.W. Rankin, “The effects of piston shape on the performance of a 5.2 L SI engine,” 1998 Spring Technical Meeting, The Combustion Institute, Canadian Section, Paper 5, 5 pages.
10 D.S-K. Ting, M.D. Checkel, “Combustion process in internal combustion engines: the development of spark-ignited, premixed turbulent flames in a combustion chamber,” the Third Asian-Pacific International Symposium on Combustion and Energy Utilization, 6 pages, December 1995.
9 D.S-K. Ting, M.D. Checkel, “The early combustion process in a spark-ignition engine: preference for small-scale turbulence enhancement,” the 15th Canadian Congress of Applied Mechanics, CANCAM 1995, 2 pages.
8 D.S-K. Ting, M.D. Checkel, “Spark-ignited, ultra lean, premixed methane-air flame propagation in a combustion chamber,” 1995 Spring Technical Meeting, The Combustion Institute, Canadian Section, 6 pages.
7 D.S-K. Ting, M.D. Checkel, W.T. Ashurst, “Turbulent burning velocity: dependence upon flame size, flow length scale and velocity intensity,” work-in-progress poster section, The Twenty-Fifth International Symposium on Combustion, August 1994.
6 D.S-K. Ting, M.D. Checkel, “Spark ignited flame propagation in a turbulent flow field,” the Eleventh Canadian Symposium on Fluid Dynamics, 2 pages, June 1994.
5 D.S-K. Ting, M.D. Checkel, “Modelling turbulent flame propagation in a chamber,” 1994 Spring Technical Meeting, The Combustion Institute, Canadian Section, 5 pages.
4 W.T. Ashurst, M.D. Checkel, D.S-K. Ting, “The eddy structure model of turbulent flamelet propagation, the expanding spherical and steady planar cases,” 1993 Fall Technical Meeting, The Combustion Institute, Eastern States Section, USA (Also presented at the Western States Section), Paper 93-060, 30 pages.
3 D.S-K. Ting, M.D. Checkel, “Modelling turbulent flame growth in a combustion chamber,” 1993 Spring Technical Meeting, The Combustion Institute, Canadian Section, Paper 33, 4 pages.
2 M.D. Checkel, D.S-K. Ting, “Turbulence effects on developing flames,” 1992 Spring Technical Meeting, The Combustion Institute, Canadian Section, pp. 22-25.
1 M.D. Checkel, D.S-K. Ting, W.K. Bushe, “Examination of the flammability of ammonia / nitric oxide mixtures,” 1990 Spring Technical Meeting, The Combustion Institute, Canadian and Western States Sections, pp. 143-146.
